Search results

Create the page "It" on this wiki! See also the search results found.

Ubuntu - Client Installation
...own into logical steps that will help allow for any troubleshooting should it be required. Don't let the long contents fool you. It's not a complicated process and in fact is a great way for new SatNOGS user

15 KB (2,008 words) - 05:16, 20 November 2022
Get In Touch
...ibrespacefoundation/satnogs/ Gitlab repository]. (If you're not sure where it should go, feel free to ask on [https://community.libre.space the web forum

1 KB (231 words) - 15:09, 15 June 2021
SatNOGS Arduino Uno/CNC Shield Based Rotator Controller
...onent that is part of a SatNOGS ground station. There may be occasion when it is desirable to have a stand alone ground station that is removed from the ...nnect your Rotator controller DIRECTLY TO A PC. If you'd like to still use it with the Raspberry Pi then you must keep the RS485 protocol in place.

28 KB (2,926 words) - 22:23, 24 March 2020
SatNOGS Rotator Controller
*It is designed to fit the entire electronics needed to control rotator in Euro *Default communication interface is RS-485 but it can also be used as a UART.

18 KB (2,569 words) - 00:55, 2 September 2021
Fedora Installation
* Connect SD card to your computer/laptop and prepare it as described at [https://fedoraproject.org/wiki/Raspberry_Pi#Preparing_the_ ** Defines the sdr device. It could be 'usrpb200' or 'rtlsdr'.

16 KB (2,355 words) - 16:28, 20 January 2020
Software contribution
...s written in Python, targeting raspberry pi as the reference architecture. It interfaces with the following applications:

3 KB (455 words) - 21:38, 19 January 2020
SatNOGS Client Setup
...roubleshooting#Invalid_Signature_for_download.opensuse.org on how to solve it}}In case of getting a similar error to "Newer kernel available" annoying me ...you don't have a rotator (like the [[No rotator|No rotator setup]]), leave it empty.

18 KB (2,595 words) - 17:24, 10 September 2022
Omnidirectional Station How To
...a FM transponder. But for CubeSats with 1 watt transmitters at 9600 baud, it's going to be really difficult to actually decode any data with an omni ant {{Warning|WARNING: This section was recently added. Please test and if it works, remove this banner.}}

27 KB (4,348 words) - 11:10, 26 October 2021
Adjusting the SatNOGS Client
...This means any calibration values determined below will not be consistent. It is highly recommended that you purchase a SDR which utilises a temperature At the moment you probably have to get and build it by yourself.

14 KB (2,250 words) - 10:25, 7 November 2020
Software Defined Radio
...the voltage, but through initial testing (as of this writing, 17 Aug 2019) it seems that the following procedure works best. ...turn on the bias-t with the command <code>./rtl_biast -b 1</code> and turn it off with <code>./rtl_biast -b 0</code>. Note that the developers of this

17 KB (2,647 words) - 08:52, 9 August 2022
Rotators
(okay, you're not likely to keep a deep space observatory on the network, but it has been done!)

3 KB (490 words) - 17:39, 1 May 2021
SDR Setup
It provides a source block for signal reception and a sink block for signal tr It also provides blocks for debugging and experimenting with known satellite t

12 KB (1,619 words) - 19:19, 19 March 2020
Antennas
...should be avoided. The following are considered suitable choices:</p><p>'''It is highly recommended that you use a mast-mounted Low-Noise Amplifier (LNA)

10 KB (1,519 words) - 06:25, 26 August 2021
No rotator
...in the stations performance being significantly limited by its own noise. It is advisable to mount the LNA at the antenna, and the rest of the station a

4 KB (621 words) - 09:25, 7 November 2020
Observations
...r some modes there are a variety of baud rates and other factors that make it so two identical modes might not necessarily look similar. For further comm

5 KB (686 words) - 19:08, 18 February 2020
Observe
...fall_1365407_2019-12-13T02-15-35.png|SatNOGS Client uploaded an image, but it is a solid color.

5 KB (755 words) - 12:28, 21 August 2020
SatNOGS Rotator v3
...your own 3d printer, then a local Fab Lab or hackerspace may be able to do it for you. Fab Labs and hackerspaces are places that have invested in the mac File:C1062-1.png|C1062-1, It is recommended to build in laser sintering like Shapeways with White Versat

31 KB (4,751 words) - 06:38, 8 September 2022
Raspberry Pi
You can log in the Raspberry Pi by connecting it to a keyboard and monitor or through network via an SSH connection.

6 KB (854 words) - 21:41, 20 February 2024
Academic Papers
...with any other research paper that mentions SatNOGS, don't hesitate to add it to the list!

15 KB (2,177 words) - 03:14, 11 June 2021