Difference between revisions of "Raspberry Pi"
From SatNOGS Wiki
| Line 11: | Line 11: | ||
= Raspbian = | = Raspbian = | ||
| − | |||
| − | |||
| + | == Download == | ||
| + | Latest Raspbian SatNOGS image artifacts can be downloaded from [https://gitlab.com/librespacefoundation/satnogs/satnogs-pi-gen/tags GitLab]. | ||
| + | |||
| + | === Artifacts list === | ||
| + | The current artifacts list consists of: | ||
| + | * A Zipped image file | ||
| + | * An Image info file | ||
| + | * A SHA256 checksums file | ||
| + | |||
| + | == Data integrity verification == | ||
| + | You should verify the data integrity of the artifacts by checking the SHA256 checksums. On Linux, run <code>sha256sum -c sha256sums</code> in the directory where the artifacts are downloaded | ||
| + | |||
| + | Example: | ||
<pre> | <pre> | ||
| − | + | $ sha256sum -c sha256sums | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
2017-09-10-Raspbian-SatNOGS-master-lite.info: OK | 2017-09-10-Raspbian-SatNOGS-master-lite.info: OK | ||
image_2017-09-10-Raspbian-SatNOGS-master-lite.zip: OK | image_2017-09-10-Raspbian-SatNOGS-master-lite.zip: OK | ||
</pre> | </pre> | ||
| + | == Flashing == | ||
| − | + | [https://www.raspberrypi.org/documentation/installation/installing-images/README.md Follow the usual Raspbian flashing instructions], and boot your Raspberry Pi. | |
| − | |||
| − | |||
| − | / | ||
| − | |||
| − | |||
| − | |||
| − | + | == Networking == | |
If you are using wired ethernet you should get connectivity right away. If you are using wireless then see [https://www.raspberrypi.org/documentation/configuration/wireless/wireless-cli.md this doc for network configuration instructions]. | If you are using wired ethernet you should get connectivity right away. If you are using wireless then see [https://www.raspberrypi.org/documentation/configuration/wireless/wireless-cli.md this doc for network configuration instructions]. | ||
| + | == Setup == | ||
SSH to the Raspberry Pi with user "pi" and password "raspberry" (no quotes). Run "sudo satnogs-setup" to set basic configuration. When it's done, the Raspberry Pi will reconfigure itself; this may take some time. | SSH to the Raspberry Pi with user "pi" and password "raspberry" (no quotes). Run "sudo satnogs-setup" to set basic configuration. When it's done, the Raspberry Pi will reconfigure itself; this may take some time. | ||
* Note: you can always reconfigure the software by running "sudo satnogs-setup -n" again. | * Note: you can always reconfigure the software by running "sudo satnogs-setup -n" again. | ||
Revision as of 10:28, 30 September 2017
The Raspberry Pi 3 is the reference platform for SatNOGs. As of September 2017, there are two methods of installing the SatNOGS client on a Raspberry Pi:
- Using Fedora for ARM, and following the instructions at satnogs.readthedocs.io
- Installing the custom-built SatNOGS Raspian image
Contents
Fedora
Start by downloading the "Server" or "Minimal" image from the the Fedora ARM project page. After that, follow the instructions at satnogs.readthedocs.io.
- If you run into anything in the instructions that is unclear, please submit an issue against the documentation repository.
Raspbian
Download
Latest Raspbian SatNOGS image artifacts can be downloaded from GitLab.
Artifacts list
The current artifacts list consists of:
- A Zipped image file
- An Image info file
- A SHA256 checksums file
Data integrity verification
You should verify the data integrity of the artifacts by checking the SHA256 checksums. On Linux, run sha256sum -c sha256sums in the directory where the artifacts are downloaded
Example:
$ sha256sum -c sha256sums 2017-09-10-Raspbian-SatNOGS-master-lite.info: OK image_2017-09-10-Raspbian-SatNOGS-master-lite.zip: OK
Flashing
Follow the usual Raspbian flashing instructions, and boot your Raspberry Pi.
Networking
If you are using wired ethernet you should get connectivity right away. If you are using wireless then see this doc for network configuration instructions.
Setup
SSH to the Raspberry Pi with user "pi" and password "raspberry" (no quotes). Run "sudo satnogs-setup" to set basic configuration. When it's done, the Raspberry Pi will reconfigure itself; this may take some time.
- Note: you can always reconfigure the software by running "sudo satnogs-setup -n" again.
