SatNOGS Arduino Uno/CNC Shield Based Rotator Controller

Controlling the rotator as a stand alone system using GPredict

The SatNOGS rotator is primarily designed to be used as a system component that is part of a SatNOGS ground station. There may be occasion when it is desirable to have a stand alone ground station that is removed from the SatNOGS network. This can be done using existing equipment but can also be simplified using off the shelf components.

The following information is to connect your Rotator controller DIRECTLY TO A PC. If you'd like to still use it with the Raspberry Pi then you must keep the RS485 protocol in place.

We will need slightly different hardware and modified software to achieve this, the main changes will be to remove the RS485 and watchdog parts of the firmware. We will be using the following items:

Hardware

1. SatNOGS Rotator V3.1 hardware
2. Arduino Uno R3
3. CNC Shield V3 with A4988 drivers
4. NEMA 17 Stepper Motors
5. 2x microswitches
6. Suitable 12v power supply (The shield will accept between 12v and 36v)
7. Cables to connect the Arduino to the PC

Software

For the purposes of this article we will be using Windows software. The same result can be achieved with Linux or Mac OS but for clarity these options have been ignored for the time being. We will need:

1. A copy of the Arduino IDE (version 1.8.5 has been used as part of this tutorial)
2. GPredict
3. Hamlib
4. A text editor such as Notepad++ for a small script

Method

Hardware setup

We will not be using the custom SatNOGS PCB. Instead this set up uses an Arduino Uno and CNC motor shield. There is very little assembly required but depending on how and where you buy from will depend on the amount of assembly is required. Typically the Arduino will need no assembly, The motor shield will need two A4988 drivers (these can come as part of the package). These are used in the X & Y headers as per the photograph below. The drivers fit into the female headers, note that there are jumper headers below these drivers that are used for stepping control. We will also be attaching the stepper motor cables to the male headers to the left of the driver boards.

Photo of board

Pinout of the 4 headers is as follows starting from the top

Pin 1 - A

Pin 2 - A+

Pin 3 - B

Pin 4 - B+

This follows a convention so most steppers should plug directly into the header without any changes, but be aware that this is not always the case and that there may be some cases where pins are incorrectly noted and the steppers will drive in the opposite direction.

The setup is very basic but be careful not to bend pins as this can be easily done if too much pressure is put on the boards when things are no aligned. They aren't always perfect!

In the end you should have:

• Azimuth Stepper Driver/motor connected to Y port on CNC Board
• Elevation Stepper Driver/motor connected to X port on CNC Board
• The End stop switch for elevation is connected to the X end stop on the CNC board (+ or -)
• The End stop switch for azimuth is connected to the Y end stop on the CNC board (+ or -)

Software setup

Code modifications

For the time being there is no fork of the firmware in the repositories. This may change in the future but for the time being a small series of changes are required to achieve results. We will need to modify two elements of the firmware, easycomm.h and rotator_pins.h. These changes are necessary to stop their being conflicts with the communication between boards and PC as well as re-assigning pins to match the CNC shield. We'll modify the rotator_pins.h first. Note the use of comments (//) to remove lines of code. We have also changed pin designation to match the shield.

   /*!
   * @file rotator_pins.h
   *
   * It is a header file for pin mapping.
   *
   * Licensed under the GPLv3
   *
   */

   #ifndef ROTATOR_PINS_H_
   #define ROTATOR_PINS_H_

   //#define M1IN1 10 ///< Motor 1 PWM pin
   #define M1IN1 2 ///< Motor 1 PWM pin
   #define M1IN2 5  ///< Motor 1 PWM pin
   #define M1SF  7  ///< Motor 1 digital input, status flag for DC Motor Drivers
   #define M1FB  A1 ///< Motor 1 analog input, current/load feedback for DC Motor Drivers

   #define M2IN1 3 ///< Motor 2 PWM pin
   #define M2IN2 6  ///< Motor 2 PWM pin
   #define M2SF  7 ///< Motor 2 digital input, status flag for DC Motor Drivers
   #define M2FB  A0 ///< Motor 2 analog input, current/load feedback for DC Motor Drivers

   #define MOTOR_EN 8 ///< Digital output, to enable the motors

   #define SW1 11 ///< Digital input, to read the status of end-stop for motor 1
   #define SW2 9 ///< Digital input, to read the status of end-stop for motor 2

   #define RS485_DIR 2 ///< Digital output, to set the direction of RS485 communication

   #define SDA_PIN 3 ///< I2C data pin
   #define SCL_PIN 4 ///< I2C clock pin

   #define PIN12 12 ///< General purpose I/O pin
   #define PIN13 13 ///< General purpose I/O pin
   #define A2    A2 ///< General purpose I/O & analog pin
   #define A3    A3 ///< General purpose I/O & analog pin

   #endif /* ROTATOR_PINS_H_ */

The next code edit will remove both the RS485 and watchdog elements from the easycomm.h code. This will allow the PC to talk directly to the Arduino and as such bypass the RPi. The edited code is below, note again the use of comments (//) to remove the lines

   /*!
   * @file easycomm.h
   *
   * It is a driver for easycomm 3 protocol as referred, in Hamlib.
   *
   * Licensed under the GPLv3
   *
   */

   #ifndef LIBRARIES_EASYCOMM_H_
   #define LIBRARIES_EASYCOMM_H_

   #include <Arduino.h>
   #include <WString.h>
   #include <avr/wdt.h>
   //#include "rs485.h"
   #include "rotator_pins.h"
   #include "globals.h"

   #define RS485_TX_TIME 9     ///< Delay "t"ms to write in serial for RS485 implementation
   #define BUFFER_SIZE   256   ///< Set the size of serial buffer
   #define BAUDRATE      19200 ///< Set the Baudrate of easycomm 3 protocol

   //rs485 rs485(RS485_DIR, RS485_TX_TIME);

   /**************************************************************************/
   /*!
       @brief    Class that functions for easycomm 3 implementation
   */
   /**************************************************************************/
   class easycomm {
   public:

       /**************************************************************************/
       /*!
           @brief    Initialize the RS485 bus
       */
       /**************************************************************************/
       void easycomm_init() {
          // rs485.begin(BAUDRATE);
   	    Serial.begin(9600);
       }

       /**************************************************************************/
       /*!
           @brief    Get the commands from RS485 and response to the client
       */
       /**************************************************************************/
       void easycomm_proc() {
           char buffer[BUFFER_SIZE];
           char incomingByte;
           char *Data = buffer;
           char *rawData;
           static uint16_t BufferCnt = 0;
           char data[100];
           String str1, str2, str3, str4, str5, str6;

           // Read from serial
           while (Serial.available() > 0) {
               incomingByte = Serial.read();

               // Read new data, '\n' means new pacakage
               if (incomingByte == '\n' || incomingByte == '\r') {
                   buffer[BufferCnt] = 0;
                   if (buffer[0] == 'A' && buffer[1] == 'Z') {
                       if (buffer[2] == ' ' && buffer[3] == 'E' &&
                           buffer[4] == 'L') {
                           // Send current absolute position in deg
                           str1 = String("AZ");
                           str2 = String(control_az.input, 1);
                           str3 = String(" EL");
                           str4 = String(control_el.input, 1);
                           str5 = String("\n");
                           Serial.print(str1 + str2 + str3 + str4 + str5);
                       } else {
                           // Get the absolute position in deg for azimuth
                           rotator.control_mode = position;
                           rawData = strtok_r(Data, " ", &Data);
                           strncpy(data, rawData + 2, 10);
                           if (isNumber(data)) {
                               control_az.setpoint = atof(data);
                           }
                           // Get the absolute position in deg for elevation
                           rawData = strtok_r(Data, " ", &Data);
                           if (rawData[0] == 'E' && rawData[1] == 'L') {
                               strncpy(data, rawData + 2, 10);
                               if (isNumber(data)) {
                                   control_el.setpoint = atof(data);
                               }
                           }
                       }
                   } else if (buffer[0] == 'E' && buffer[1] == 'L') {
                           // Get the absolute position in deg for elevation
                           rotator.control_mode = position;
                           rawData = strtok_r(Data, " ", &Data);
                           if (rawData[0] == 'E' && rawData[1] == 'L') {
                               strncpy(data, rawData + 2, 10);
                               if (isNumber(data)) {
                                   control_el.setpoint = atof(data);
                               }
                           }
                   } else if (buffer[0] == 'V' && buffer[1] == 'U') {
                       // Elevation increase speed in mdeg/s
                       rotator.control_mode = speed;
                       strncpy(data, Data + 2, 10);
                       if (isNumber(data)) {
                           // Convert to deg/s
                           control_el.setpoint_speed = atof(data) / 1000;
                       }
                   } else if (buffer[0] == 'V' && buffer[1] == 'D') {
                       // Elevation decrease speed in mdeg/s
                       rotator.control_mode = speed;
                       strncpy(data, Data + 2, 10);
                       if (isNumber(data)) {
                           // Convert to deg/s
                           control_el.setpoint_speed = - atof(data) / 1000;
                       }
                   } else if (buffer[0] == 'V' && buffer[1] == 'L') {
                       // Azimuth increase speed in mdeg/s
                       rotator.control_mode = speed;
                       strncpy(data, Data + 2, 10);
                       if (isNumber(data)) {
                           // Convert to deg/s
                           control_az.setpoint_speed = atof(data) / 1000;
                       }
                   } else if (buffer[0] == 'V' && buffer[1] == 'R') {
                       // Azimuth decrease speed in mdeg/s
                       rotator.control_mode = speed;
                       strncpy(data, Data + 2, 10);
                       if (isNumber(data)) {
                           // Convert to deg/s
                           control_az.setpoint_speed = - atof(data) / 1000;
                       }
                   } else if (buffer[0] == 'S' && buffer[1] == 'A' &&
                              buffer[2] == ' ' && buffer[3] == 'S' &&
                              buffer[4] == 'E') {
                       // Stop Moving
                       rotator.control_mode = position;
                       str1 = String("AZ");
                       str2 = String(control_az.input, 1);
                       str3 = String(" EL");
                       str4 = String(control_el.input, 1);
                       str5 = String("\n");
                       Serial.print(str1 + str2 + str3 + str4 + str5);
                       control_az.setpoint = control_az.input;
                       control_el.setpoint = control_el.input;
                   } else if (buffer[0] == 'R' && buffer[1] == 'E' &&
                              buffer[2] == 'S' && buffer[3] == 'E' &&
                              buffer[4] == 'T') {
                       // Reset the rotator, go to home position
                       str1 = String("AZ");
                       str2 = String(control_az.input, 1);
                       str3 = String(" EL");
                       str4 = String(control_el.input, 1);
                       str5 = String("\n");
                       Serial.print(str1 + str2 + str3 + str4 + str5);
                       rotator.homing_flag = false;
                   } else if (buffer[0] == 'P' && buffer[1] == 'A' &&
                              buffer[2] == 'R' && buffer[3] == 'K' ) {
                       // Park the rotator
                       rotator.control_mode = position;
                       str1 = String("AZ");
                       str2 = String(control_az.input, 1);
                       str3 = String(" EL");
                       str4 = String(control_el.input, 1);
                       str5 = String("\n");
                       Serial.print(str1 + str2 + str3 + str4 + str5);
                       control_az.setpoint = rotator.park_az;
                       control_el.setpoint = rotator.park_el;
                   } else if (buffer[0] == 'V' && buffer[1] == 'E') {
                       // Get the version if rotator controller
                       str1 = String("VE");
                       str2 = String("SatNOGS-v2.2");
                       str3 = String("\n");
                       Serial.print(str1 + str2 + str3);
                   } else if (buffer[0] == 'I' && buffer[1] == 'P' &&
                              buffer[2] == '0') {
                       // Get the inside temperature
                       str1 = String("IP0,");
                       str2 = String(rotator.inside_temperature, DEC);
                       str3 = String("\n");
                       Serial.print(str1 + str2 + str3);
                   } else if (buffer[0] == 'I' && buffer[1] == 'P' &&
                              buffer[2] == '1') {
                       // Get the status of end-stop, azimuth
                       str1 = String("IP1,");
                       str2 = String(rotator.switch_az, DEC);
                       str3 = String("\n");
                       Serial.print(str1 + str2 + str3);
                   } else if (buffer[0] == 'I' && buffer[1] == 'P' &&
                              buffer[2] == '2') {
                       // Get the status of end-stop, elevation
                       str1 = String("IP2,");
                       str2 = String(rotator.switch_el, DEC);
                       str3 = String("\n");
                       Serial.print(str1 + str2 + str3);
                   } else if (buffer[0] == 'I' && buffer[1] == 'P' &&
                              buffer[2] == '3') {
                       // Get the current position of azimuth in deg
                       str1 = String("IP3,");
                       str2 = String(control_az.input, 2);
                       str3 = String("\n");
                       Serial.print(str1 + str2 + str3);
                   } else if (buffer[0] == 'I' && buffer[1] == 'P' &&
                              buffer[2] == '4') {
                       // Get the current position of elevation in deg
                       str1 = String("IP4,");
                       str2 = String(control_el.input, 2);
                       str3 = String("\n");
                       Serial.print(str1 + str2 + str3);
                   } else if (buffer[0] == 'I' && buffer[1] == 'P' &&
                              buffer[2] == '5') {
                       // Get the load of azimuth, in range of 0-1023
                       str1 = String("IP5,");
                       str2 = String(control_az.load, DEC);
                       str3 = String("\n");
                       Serial.print(str1 + str2 + str3);
                   } else if (buffer[0] == 'I' && buffer[1] == 'P' &&
                              buffer[2] == '6') {
                       // Get the load of elevation, in range of 0-1023
                       str1 = String("IP6,");
                       str2 = String(control_el.load, DEC);
                       str3 = String("\n");
                       Serial.print(str1 + str2 + str3);
                   } else if (buffer[0] == 'I' && buffer[1] == 'P' &&
                              buffer[2] == '7') {
                       // Get the speed of azimuth in deg/s
                       str1 = String("IP7,");
                       str2 = String(control_az.speed, 2);
                       str3 = String("\n");
                       Serial.print(str1 + str2 + str3);
                   } else if (buffer[0] == 'I' && buffer[1] == 'P' &&
                              buffer[2] == '8') {
                       // Get the speed of elevation in deg/s
                       str1 = String("IP8,");
                       str2 = String(control_el.speed, 2);
                       str3 = String("\n");
                       Serial.print(str1 + str2 + str3);
                   } else if (buffer[0] == 'G' && buffer[1] == 'S') {
                       // Get the status of rotator
                       str1 = String("GS");
                       str2 = String(rotator.rotator_status, DEC);
                       str3 = String("\n");
                       Serial.print(str1 + str2 + str3);
                   } else if (buffer[0] == 'G' && buffer[1] == 'E') {
                       // Get the error of rotator
                       str1 = String("GE");
                       str2 = String(rotator.rotator_error, DEC);
                       str3 = String("\n");
                       Serial.print(str1 + str2 + str3);
                   } else if(buffer[0] == 'C' && buffer[1] == 'R') {
                       // Get Configuration of rotator
                       if (buffer[3] == '1') {
                           // Get Kp Azimuth gain
                           str1 = String("1,");
                           str2 = String(control_az.p, 2);
                           str3 = String("\n");
                           Serial.print(str1 + str2 + str3);
                       } else if (buffer[3] == '2') {
                           // Get Ki Azimuth gain
                           str1 = String("2,");
                            str2 = String(control_az.i, 2);
                            str3 = String("\n");
                            Serial.print(str1 + str2 + str3);
                       } else if (buffer[3] == '3') {
                           // Get Kd Azimuth gain
                           str1 = String("3,");
                           str2 = String(control_az.d, 2);
                           str3 = String("\n");
                           Serial.print(str1 + str2 + str3);
                       } else if (buffer[3] == '4') {
                           // Get Kp Elevation gain
                           str1 = String("4,");
                            str2 = String(control_el.p, 2);
                            str3 = String("\n");
                            Serial.print(str1 + str2 + str3);
                       } else if (buffer[3] == '5') {
                           // Get Ki Elevation gain
                           str1 = String("5,");
                           str2 = String(control_el.i, 2);
                           str3 = String("\n");
                           Serial.print(str1 + str2 + str3);
                       } else if (buffer[3] == '6') {
                           // Get Kd Elevation gain
                           str1 = String("6,");
                           str2 = String(control_el.d, 2);
                           str3 = String("\n");
                           Serial.print(str1 + str2 + str3);
                       } else if (buffer[3] == '7') {
                           // Get Azimuth park position
                           str1 = String("7,");
                           str2 = String(rotator.park_az, 2);
                           str3 = String("\n");
                           Serial.print(str1 + str2 + str3);
                       } else if (buffer[3] == '8') {
                           // Get Elevation park position
                           str1 = String("8,");
                           str2 = String(rotator.park_el, 2);
                           str3 = String("\n");
                           Serial.print(str1 + str2 + str3);
                       } else if (buffer[3] == '9') {
                           // Get control mode
                           str1 = String("9,");
                           str2 = String(rotator.control_mode);
                           str3 = String("\n");
                           Serial.print(str1 + str2 + str3);
                       }
                   } else if (buffer[0] == 'C' && buffer[1] == 'W') {
                       // Set Config
                       if (buffer[2] == '1') {
                           // Set Kp Azimuth gain
                           rawData = strtok_r(Data, ",", &Data);
                           strncpy(data, rawData + 4, 10);
                           if (isNumber(data)) {
                               control_az.p = atof(data);
                           }
                       } else if (buffer[2] == '2') {
                           // Set Ki Azimuth gain
                           rawData = strtok_r(Data, ",", &Data);
                           strncpy(data, rawData + 4, 10);
                           if (isNumber(data)) {
                               control_az.i = atof(data);
                           }
                       } else if (buffer[2] == '3') {
                           // Set Kd Azimuth gain
                           rawData = strtok_r(Data, ",", &Data);
                           strncpy(data, rawData + 4, 10);
                           if (isNumber(data)) {
                               control_az.d = atof(data);
                           }
                       } else if (buffer[2] == '4') {
                           // Set Kp Elevation gain
                           rawData = strtok_r(Data, ",", &Data);
                           strncpy(data, rawData + 4, 10);
                           if (isNumber(data)) {
                               control_el.p = atof(data);
                           }
                       } else if (buffer[2] == '5') {
                           // Set Ki Elevation gain
                           rawData = strtok_r(Data, ",", &Data);
                           strncpy(data, rawData + 4, 10);
                           if (isNumber(data)) {
                               control_el.i = atof(data);
                           }
                       } else if (buffer[2] == '6') {
                           // Set Kd Elevation gain
                           rawData = strtok_r(Data, ",", &Data);
                           strncpy(data, rawData + 4, 10);
                           if (isNumber(data)) {
                               control_el.d = atof(data);
                           }
                       }  else if (buffer[2] == '7') {
                           // Set the Azimuth park position
                           rawData = strtok_r(Data, ",", &Data);
                           strncpy(data, rawData + 4, 10);
                           if (isNumber(data)) {
                               rotator.park_az = atof(data);
                           }
                       } else if (buffer[2] == '8') {
                           // Set the Elevation park position
                           rawData = strtok_r(Data, ",", &Data);
                           strncpy(data, rawData + 4, 10);
                           if (isNumber(data)) {
                               rotator.park_el = atof(data);
                           }
                       }
                   } else if (buffer[0] == 'R' && buffer[1] == 'S'
                           && buffer[2] == 'T') {
                       // Custom command to test the watchdog timer routine
                       while(1)
                           ;
                   } else if (buffer[0] == 'R' && buffer[1] == 'B') {
                       // Custom command to reboot the uC
                       wdt_enable(WDTO_2S);
                       while(1);
                   }
                   // Reset the buffer an clean the serial buffer
                   BufferCnt = 0;
                   Serial.flush();
               } else {
                   // Fill the buffer with incoming data
                   buffer[BufferCnt] = incomingByte;
                   BufferCnt++;
               }
           }
       }

   private:
       bool isNumber(char *input) {
           for (uint16_t i = 0; input[i] != '\0'; i++) {
               if (isalpha(input[i]))
                   return false;
           }
           return true;
       }
   };

   #endif /* LIBRARIES_EASYCOMM_H_ */

Software to install

Final pieces to the preparation work are to install a couple of pieces of software. firstly Hamlib. This will be used to communicate between GPredict and the Arduino. Secondly we will install the main prediction software, GPredict. We will not be going into detail about setup of GPredict but assume that you have followed the installation guide and had a play around with it so you can understand what it is and how it works.

Install hamlib

Download the software and follow the installation process. this may require you installing it with Administrator rights. using device manager find the port for the Arduino, for the purposes of this we will assume it is COM7

Install Hamlib: https://sourceforge.net/projects/hamlib/

create a .bat file in the same folder as rotctld (I found it in C:\Program Files (x86)\hamlib-w64-3.2\bin ) with the following (modify for your com port)

rotctld -m 202 -r COM7 -s 9600 -T 127.0.0.1 -t 4533 -C timeout=500 -C retry=0 -vvvvvvvv > pause

Download Gpredict https://sourceforge.net/projects/gpredict/

Edit...Preferences...Interfaces...Rotators...Add New Name host port Arduino localhost 4533

Start your .bat, in the top right corner of Gpredict, click down arrow, then 'Antenna Control'

...Clicking 'Engage' should get the Rotator to start working.

Once you have configured some satellites you can them select them and click 'Track'

Tweaks

There is a huge variety in parts that can get bought, here are a few tweaks that may be necessary.

Motors are turning the wrong way - This may need the pins checking

It is only moving half the distance - Change the gear ratio in the main sketch

The limit switches are not working - Change the following code in the main sketch

define DEFAULT_HOME_STATE LOW ///< Change to LOW according to Home sensor