Difference between revisions of "SatNOGS Rotator v2"
From SatNOGS Wiki
(Add more info about the v2 rotator) |
|||
| Line 1: | Line 1: | ||
| + | {{Template:Rotator | ||
| + | |Rotator-Name=SatNOGS Rotator v2 | ||
| + | |image= 29854586940 d47e229453 k.jpg | ||
| + | |type= Az/El | ||
| + | |cost= ~200 (with electronics) | ||
| + | |status= Beta | ||
| + | |latest-release= https://gitlab.com/librespacefoundation/satnogs/satnogs-rotator/tags/v2.0 | ||
| + | |latest-release-name= v2 | ||
| + | |source-repo= https://gitlab.com/librespacefoundation/satnogs/satnogs-rotator/ gitlab | ||
| + | |documentation= https://satnogs.dozuki.com/c/SatNOGS_Hardware dozuki | ||
| + | }} | ||
| + | |||
| + | == Intro == | ||
| + | |||
| + | v2 is the first attempt to build a rotator for SatNOGS project. | ||
| + | |||
| + | |||
| + | [[File:30033213301 ef78e64120 k.jpg|thumb|center|800x420px|alt=|Inside the v2 rotator]] | ||
| + | |||
| + | |||
| + | == Assembly == | ||
| + | |||
Assembly instructions can be found [https://satnogs.dozuki.com/Guide/SatNOGS+Ground+Station+v2+Electronics+Assembly/2 here]. | Assembly instructions can be found [https://satnogs.dozuki.com/Guide/SatNOGS+Ground+Station+v2+Electronics+Assembly/2 here]. | ||
| − | v2 | + | All the parts are placed [https://gitlab.com/librespacefoundation/satnogs/satnogs-rotator/tags/v2.0 here]. |
| + | The electronics and firmware to control the motors are placed [https://gitlab.com/librespacefoundation/satnogs/satnogs-rotator-controller/tags/v1 here]. | ||
| + | The v2 rotator could be also controlled by the [https://gitlab.com/librespacefoundation/satnogs/satnogs-rotator-controller/tags/v2.2 v2.2] | ||
| + | controller. The [https://wiki.satnogs.org/SatNOGS_Rotator_Controller v2.2 rotator controller wiki]. | ||
| + | |||
| + | In the [https://gitlab.com/librespacefoundation/satnogs/satnogs-rotator-controller/tags/v1 v1] board the new [https://gitlab.com/librespacefoundation/satnogs/satnogs-rotator-firmware firmware] hasn't been tested. At first changes in [https://gitlab.com/librespacefoundation/satnogs/satnogs-rotator-firmware/blob/master/libraries/rotator_pins.h rotator_pins.h] header file must be done to match with v1 board pins. But the different mcu Atmega32u4, optiboot bootloader and WDT peripheral may create problems to nominal operation of the rotator. | ||
| + | |||
| + | Related posts in [https://community.libre.space/ libre space community]: | ||
| + | |||
| + | * [https://community.libre.space/t/design-files-for-satnogs-v2-box/468 Design files for SatNOGS v2 box] | ||
| + | * [https://community.libre.space/t/iz5rzr-satnogs-v-2-from-italy/1001 IZ5RZR Satnogs V.2 from Italy] | ||
| + | * [https://community.libre.space/t/newbie-wants-to-build-a-v2-ground-station/3189 Newbie wants to build a V2 ground station] | ||
Revision as of 14:32, 24 January 2019
| SatNOGS Rotator v2 | |
|---|---|
| Rotator Information | |
| Type: | Az/El |
| Cost: | ~200 (with electronics) |
| Release Information | |
| Status: | Beta |
| Latest Release: | v2 |
| Repository: | gitlab |
| Documentation: | dozuki |
Intro
v2 is the first attempt to build a rotator for SatNOGS project.
Assembly
Assembly instructions can be found here.
All the parts are placed here. The electronics and firmware to control the motors are placed here. The v2 rotator could be also controlled by the v2.2 controller. The v2.2 rotator controller wiki.
In the v1 board the new firmware hasn't been tested. At first changes in rotator_pins.h header file must be done to match with v1 board pins. But the different mcu Atmega32u4, optiboot bootloader and WDT peripheral may create problems to nominal operation of the rotator.
Related posts in libre space community:
