Difference between revisions of "PE1CKK Az-El rotator"
From SatNOGS Wiki
(added BOM) (Tag: Visual edit) |
(→Sourcing & parts: add table "3D-printed parts") (Tag: Visual edit) |
||
| Line 43: | Line 43: | ||
===Sourcing & parts=== | ===Sourcing & parts=== | ||
[https://pad.tchncs.de/sheet/#/2/sheet/view/AfIfw2d1qwsnxny3PwVpOHarpkMlnl2fUeAyfzKnC3A/ Bill-of-materials (collaborative sheet)]<!-- editable link: https://pad.tchncs.de/sheet/#/2/sheet/edit/f9IAOteizSAx2Q5gZtsA5vyh/ --> | [https://pad.tchncs.de/sheet/#/2/sheet/view/AfIfw2d1qwsnxny3PwVpOHarpkMlnl2fUeAyfzKnC3A/ Bill-of-materials (collaborative sheet)]<!-- editable link: https://pad.tchncs.de/sheet/#/2/sheet/edit/f9IAOteizSAx2Q5gZtsA5vyh/ --> | ||
| + | |||
| + | ==== 3D-printed Parts ==== | ||
{| class="wikitable" | {| class="wikitable" | ||
| − | |Part | + | |'''Part''' |
| − | |Quantity | + | |'''Model Filename''' |
| − | |Distributor | + | |'''Quantity''' |
| − | |Price (each) | + | |- |
| − | |Remarks | + | |Bottom baseplate |
| + | |baseplate_2 | ||
| + | |1 | ||
| + | |- | ||
| + | |Vertical base | ||
| + | |vertical base | ||
| + | |1 | ||
| + | |- | ||
| + | |Big gear half | ||
| + | |tandwiel_groot | ||
| + | |4 | ||
| + | |- | ||
| + | |Motor gear | ||
| + | |tandwiel_motor | ||
| + | |2 | ||
| + | |- | ||
| + | |Resistor gear | ||
| + | |tandwiel_potmeter | ||
| + | |2 | ||
| + | |- | ||
| + | |Gear clamp | ||
| + | |lagerklem | ||
| + | |2 | ||
| + | |- | ||
| + | |Standoff ring | ||
| + | |bus | ||
| + | |8 | ||
| + | |} | ||
| + | <br /> | ||
| + | |||
| + | ==== Other Parts ==== | ||
| + | {| class="wikitable" | ||
| + | |'''Part''' | ||
| + | |'''Quantity''' | ||
| + | |'''Distributor''' | ||
| + | |'''Price (each)''' | ||
| + | |'''Remarks''' | ||
|- | |- | ||
|Ball bearing: 35x44x5mm 6707-2R | |Ball bearing: 35x44x5mm 6707-2R | ||
Revision as of 11:44, 4 February 2025
| PE1CKK Az-El rotator | |
|---|---|
| [[Image:|thumb|center|PE1CKK Az-El rotator]] | |
| Rotator Information | |
| Type: | Az/El |
| Cost: | |
| Release Information | |
| Status: | |
| Latest Release: | [ ] |
| Repository: | [] |
| Documentation: | [Az-El rotator] |
Introduction
A fully 3D printed Az-El system, designed by PE1CKK.
Specification
| PE1CKK Az-El rotator | |
| Plastic Parts | 20 |
| Non Printed Parts | |
| Cost | |
| Controller Electronics | |
| Type | AZ/EL |
| Motors | 2x DC Motors |
| Speed (deg/sec) | |
| Torque (Nm) | |
| Brake Torque (Nm) | |
| Dimensions (mm) | |
| Weight (kg) | |
Sourcing & parts
Bill-of-materials (collaborative sheet)
3D-printed Parts
| Part | Model Filename | Quantity |
| Bottom baseplate | baseplate_2 | 1 |
| Vertical base | vertical base | 1 |
| Big gear half | tandwiel_groot | 4 |
| Motor gear | tandwiel_motor | 2 |
| Resistor gear | tandwiel_potmeter | 2 |
| Gear clamp | lagerklem | 2 |
| Standoff ring | bus | 8 |
Other Parts
| Part | Quantity | Distributor | Price (each) | Remarks |
| Ball bearing: 35x44x5mm 6707-2R | 4 | aliexpress | 3.00 € | - Fixed typo in bearing trade number |
| Motor: Bringsmart JGY-370 12V 10rpm | 2 | aliexpress | 5.00 € | |
| L298N bridge motor controller | 1 | aliexpress | 4.00 € |
