Difference between revisions of "SatNOGS Rotator v3"

From SatNOGS Wiki
(Fixed link to instructions for mechanical assembly)
 
(81 intermediate revisions by 15 users not shown)
Line 1: Line 1:
 
{{Template:Rotator
 
{{Template:Rotator
 
|Rotator-Name=SatNOGS Rotator v3
 
|Rotator-Name=SatNOGS Rotator v3
−
|image=
+
|image=V3.jpg
 
|type= Az/El
 
|type= Az/El
 +
|cost=~220 USD
 
|status= Beta
 
|status= Beta
−
|latest-release= https://github.com/satnogs/satnogs-rotator
+
|latest-release= https://gitlab.com/librespacefoundation/satnogs/satnogs-rotator/tags/v3.1-pre-release
−
|latest-release-name= v3
+
|latest-release-name= v3.1-pre-release
−
|source-repo= https://github.com/satnogs/satnogs-rotator
+
|source-repo= https://gitlab.com/librespacefoundation/satnogs/satnogs-rotator/
−
|documentation= http://satnogs.dozuki.com/Guide/SatNOGS+Rotator+v3+Mechanical+Assembly
+
|documentation= [https://ohai.libre.space/project/satnogs-rotator-v3-mechanical-assembly/satnogs/ v3.0.1] [https://wiki.satnogs.org/SatNOGS_Rotator_v3#Build_Sequence v3.1]
 
}}
 
}}
  
−
== Intro ==
+
==Introduction==
  
−
== Sourcing ==
+
v3 marks a major re-haul of the SatNOGS Rotator design, with learnings from [[SatNOGS Rotator v2|v2]] applied. You can see a lot of the thinking and background research that was conducted prior to v3 development in this [https://community.satnogs.org/t/satnogs-rotator-version-3/226 thread]. Also in this wiki page you can also find a "How to build the rotator", mechanical analysis and all documentation about the [https://gitlab.com/librespacefoundation/satnogs/satnogs-rotator SatNOGS rotator].
  
−
== Documentation ==
+
Also in this [https://ethercalc.net/v3specs list] is presented different rotators, either commercial or DIY builds.
 +
 
 +
==Specifications==
 +
 
 +
{| {{table}}
 +
| style="background:#f0f0f0;" align="center" |
 +
| style="background:#f0f0f0;" align="center" |'''SatNOGS v3 Rotator'''
 +
|-
 +
|Plastic Parts||15
 +
|-
 +
|Non Printed Parts||38
 +
|-
 +
|Cost||~ $220
 +
|-
 +
|Controller Electronics||[[SatNOGS Rotator Controller]]
 +
|-
 +
|Type||AZ/EL (possible X/Y)
 +
|-
 +
|Motors||2x NEMA 17 Stepper or 2x DC Motors
 +
|-
 +
|Frame Material||Aluminum T-slot 20x20
 +
|-
 +
|Speed (deg/sec)||7
 +
|-
 +
|Torque (Nm)||?, ~30
 +
|-
 +
|Brake Torque (Nm)||?
 +
|-
 +
|Dimensions (mm)||280x140x140 (AZ/EL)
 +
|-
 +
|Weight (kg)||~5
 +
|
 +
|}
 +
 
 +
====Design Goals====
 +
Considering the specifications as detailed in the [https://wiki.satnogs.org/SatNOGS_Rotator_v3#Mechanical_Analysis_.5BWIP.5D Mechanical Analysis], we would also like for the 3rd version of SatNOGS rotator to be:
 +
 
 +
*inexpensive (less than €300, if possible)
 +
*lightweight and portable (~6Kg, size:~300x~150x~150mm)
 +
*rigid and durable
 +
*easy to build and fix (try to use easily available materials)
 +
*weatherproof
 +
*electromagnetically shielded, so that noise in reception is reduced
 +
*accurate (<1deg, backlash reduction and use of encoders at the axis)
 +
 
 +
==Sourcing==
 +
 
 +
'''3d Printing at a Fab Lab or your local hackerspace:''' If you don't have your own 3d printer, then a local Fab Lab or hackerspace may be able to do it for you. Fab Labs and hackerspaces are places that have invested in the machinery and you can take the designs to them. Generally they need .stl files to import into the software that runs the machines, but this should be discussed with the Fab Lab or hackerspace. You then pay for the material, time or a combination of the two for each of the parts or any other agreement in place.
 +
 
 +
*[http://www.fabfoundation.org/fab-labs FabLabs]
 +
*[https://wiki.hackerspaces.org/List_of_Hacker_Spaces List of hacker spaces]
 +
 
 +
Most people building the rotator have had success builds with simple ABS material for the 3D printing parts.
 +
 
 +
'''T Slot''' - If you don't want to cut the pieces yourself, then you may be able to find a supplier that will do this for you.  ([http://www.kjnltd.co.uk/ Here's one in the United Kingdom].)
 +
 
 +
Hidden corner connectors - AliExpress gave the cheapest supplier
 +
 
 +
A good US source is [http://us.misumi-ec.com/ MISUMI-USA]; they will also cut to length.  MISUMI has several other global locations [https://www.misumi-ec.com].
 +
 
 +
Beware, the 20-series T-slot from [https://8020.net/ 80/20 Inc.] in the US has slots that are only 5.2mm wide.  The hidden corner connectors from e.g. AliExpress '''will not fit'''.
 +
 
 +
'''Stepper Motors''' - eBay
 +
 
 +
'''Belts''' - eBay
 +
 
 +
'''Fixings / Pipe''' - eBay
 +
 
 +
====Vendors Table====
 +
 
 +
Like the [https://reprap.org/wiki/RepRap_Buyers%27_Guide RepRap Buyers' Guide wiki], feel free to populate the table.
 +
 
 +
{| class="wikitable"
 +
|-
 +
!Vendor
 +
!Location
 +
!Parts
 +
!Notes
 +
|-
 +
|[https://www.pololu.com/ pololu]
 +
|USA, Worldwide
 +
|Motors, electronics
 +
| -
 +
|-
 +
|[http://mouser.com/ mouser]
 +
|Worldwide
 +
|Motors, electronics
 +
| -
 +
|-
 +
|[https://www.ebay.com/ ebay]
 +
|Worldwide
 +
|Motors, electronics, Fasteners, T-Slots, pulleys, Tubes
 +
| -
 +
|-
 +
|[https://www.aliexpress.com/ aliexpress]
 +
|Worldwide
 +
|Motors, electronics, Fasteners, T-Slots, pulleys, Tubes
 +
| -
 +
|-
 +
|[https://grobotronics.com/ grobotronics]
 +
|GR, EU
 +
|Motors, electronics, Fasteners, T-Slots, pulleys
 +
| -
 +
|-
 +
|[https://www.motedis.com/shop/index.php motedis]
 +
|DE, EU
 +
|T-Slots, Tubes
 +
| -
 +
|-
 +
|[https://uk.misumi-ec.com/ Misumi]
 +
|Worldwide
 +
|T-Slots, Tubes, Fasteners, Pulleys
 +
| -
 +
|-
 +
|[https://www.omc-stepperonline.com/ omc-stepperonline]
 +
|Worldwide
 +
|Stepper motors
 +
| -
 +
|-
 +
|[https://www.fastenal.ca/ fastenal]
 +
|USA
 +
|Fasteners
 +
| -
 +
|-
 +
|[https://www.mcmaster.com/ mcmaster]
 +
|USA
 +
|Fasteners
 +
| -
 +
|-
 +
|[http://www.rs-online.com/ rs]
 +
|Worldwide
 +
|Electronics, fasteners, motors
 +
| -
 +
|-
 +
|[https://8020.net/ 80/20]
 +
|USA
 +
|T-Slots
 +
| -
 +
|-
 +
|[https://www.pcbway.com/ pcbway]
 +
|CN
 +
|PCB fabrication
 +
| -
 +
|-
 +
|[https://www.servocity.com/ servocity]
 +
|USA
 +
|Motors, T-slots, fasteners
 +
|Most of parts are not metric
 +
|-
 +
 
 +
|}
 +
 
 +
==Build Sequence==
 +
 
 +
====Tools & Consumables====
 +
Here are presented tools and consumables about part fabrication, port-processing and assembly process.
 +
Most of the tools are available in every hackerspace, makerspaces, FabLabs etc.
 +
 
 +
{| class="wikitable"
 +
|-
 +
!Tool/Consumable
 +
!Description
 +
|-
 +
|Drill bits
 +
|2mm for aluminum, 3mm, 4mm and 5mm for plastic
 +
|-
 +
|Drill driver
 +
|For aluminum tube drill hole, 3D printed part
 +
|-
 +
|Sandpaper
 +
|80(dry), 120(dry), 240(dry) and 1000(wet) grit
 +
|-
 +
|Acetone
 +
|For acetone vapor bath
 +
|-
 +
|Hacksaw
 +
|For aluminum Tube
 +
|-
 +
|Square File
 +
|For worm axis, for use on steel
 +
|-
 +
|Precision Knife
 +
|For general use, especially in 3d-Printed parts
 +
|-
 +
|Caliper
 +
|Measuring Range 0-150mm
 +
|-
 +
|Combination Wrenches
 +
|5.5mm, 7mm and 8mm
 +
|-
 +
|Thread-locker
 +
|Like Loctite 271
 +
|-
 +
|Cyano acrylic glue
 +
|Like Loctite 401
 +
|-
 +
|Screw driver
 +
|Number 1 Phillips
 +
|-
 +
|Heat Gun
 +
|For Heat-shrinkables or use a lighter
 +
|-
 +
|Ball-End L-Keys
 +
|Hex 1.5mm, 2mm, 2.5mm, and 3mm
 +
|-
 +
|Soldering iron and consumables
 +
|For cables
 +
|-
 +
|Wire Cutter
 +
|For cables
 +
|-
 +
|Long-Nose Plier
 +
|General purpose
 +
|-
 +
|}
 +
 
 +
====Parts====
 +
Make sure you have all parts, according to [https://gitlab.com/librespacefoundation/satnogs/satnogs-rotator/blob/master/rotator-bom.ods BOM].
 +
 
 +
Most of the parts could be fabricated by a FDM 3D-printer. Some parts have only 2D geometry so could be
 +
fabricated by a laser cutter. Other parts have modifications of common(hardware) parts like threaded rods or
 +
aluminum pipes. Also you could find a lot of guides for [https://www.3dhubs.com/knowledge-base/post-processing-fdm-printed-parts post processing for FDM printed parts].
 +
 
 +
<gallery widths="200" heights="200" perrow="4">
 +
File:C1001.png|C1001, Aluminum Tube 6063 OD40mm TH1.5mm L240mm, 2 variants -1 and -3
 +
File:C1010-3.png|C1010-3, FDM-3Dprinted, Material: ABS, Layer height: 0.4 mm, Perimeters: 2, Top/bottom solid layers: 3, Fill density: 20%, Fill pattern: Honeycomb, Fan speed: [35, 100], No support material
 +
File:C1011-3.png|C1011-3, laser cut in 3mm Acrylic Sheet or in FDM-3Dprinter with same fabrication parameters as C1010-3
 +
File:C1020-1.png|C1020-1, FDM-3Dprinted, Material: ABS, Layer height: 0.4 mm, Perimeters: 2, Top/bottom solid layers: 3, Fill density: 20%, Fill pattern: Honeycomb, Fan speed: [35, 100], No support material, [http://sinkhacks.com/building-acetone-vapor-bath-smoothing-3d-printed-parts/ Smoothing the part with acetone vapor bath]
 +
File:C1021-1.png|C1021-1, FDM-3Dprinted, Material: ABS, Layer height: 0.4 mm, Perimeters: 2, Top/bottom solid layers: 3, Fill density: 20%, Fill pattern: Honeycomb, Fan speed: [35, 100], No support material, [http://sinkhacks.com/building-acetone-vapor-bath-smoothing-3d-printed-parts/ Smoothing the part with acetone vapor bath], [https://community.libre.space/t/version-3-1-stepper-varient-with-v2-controller/1430/5 Imperial variant], [https://community.libre.space/t/help-to-buy-metric-tubing-for-v3-rotator/784/6 tool that helps to build imperial part]
 +
File:C1022-3.png|C1022-3, laser cut in 3mm Acrylic Sheet or in FDM-3Dprinter with same fabrication parameters as C1010-3
 +
File:C1030-1.png|C1030-1, FDM-3Dprinted, Material: ABS, Layer height: 0.4 mm, Perimeters: 2, Top/bottom solid layers: 3, Fill density: 20%, Fill pattern: Honeycomb, Fan speed: [35, 100], No support material
 +
File:C1040-1.png|C1040-1, FDM-3Dprinted, Material: ABS, Layer height: 0.4 mm, Perimeters: 2, Top/bottom solid layers: 3, Fill density: 20%, Fill pattern: Honeycomb, Fan speed: [35, 100], No support material, [https://community.libre.space/t/version-3-1-stepper-varient-with-v2-controller/1430/5 Imperial variant], [https://community.libre.space/t/help-to-buy-metric-tubing-for-v3-rotator/784/6 tool that helps to build imperial part]
 +
File:C1041-1.png|C1041-1, FDM-3Dprinted, Material: ABS, Layer height: 0.4 mm, Perimeters: 2, Top/bottom solid layers: 3, Fill density: 20%, Fill pattern: Honeycomb, Fan speed: [35, 100], No support material, [https://community.libre.space/t/version-3-1-stepper-varient-with-v2-controller/1430/5 Imperial variant], [https://community.libre.space/t/help-to-buy-metric-tubing-for-v3-rotator/784/6 tool that helps to build imperial part]
 +
File:C1042-1.png|C1042-1, laser cut in 3mm Acrylic Sheet or in FDM-3Dprinter with same fabrication parameters as C1010-3
 +
File:C1043-1.png|C1043-1, FDM-3Dprinted, Material: ABS, Layer height: 0.4 mm, Perimeters: 2, Top/bottom solid layers: 3, Fill density: 20%, Fill pattern: Honeycomb, Fan speed: [35, 100], Support material, Brim Width: 2 mm
 +
File:C1050.png|C1050, Aluminum Profile 20x20 B-type slot 6, 2 variants -1 and -5
 +
File:C1060-1.png|C1060-1, M5 Threaded rod A2 stainless steel(304)
 +
File:C1061.png|C1061, 2 variants -5 and -6, FDM-3Dprinted, Material: ABS, Layer height: 0.4 mm, Perimeters: 2, Top/bottom solid layers: 3, Fill density: 20%, Fill pattern: Honeycomb, Fan speed: [35, 100], No support material
 +
File:C1062-1.png|C1062-1, It is recommended to build in laser sintering like Shapeways with White Versatile Plastic (cost ~10€) or like C1030-1 and [http://sinkhacks.com/building-acetone-vapor-bath-smoothing-3d-printed-parts/ Smoothing the part with acetone vapor bath]
 +
File:C1070-1.png|C1070-1, FDM-3Dprinted, Material: ABS, Layer height: 0.4 mm, Perimeters: 2, Top/bottom solid layers: 3, Fill density: 20%, Fill pattern: Honeycomb, Fan speed: [35, 100], No support material
 +
File:C1071-1.png|C1071-1, FDM-3Dprinted, Material: ABS, Layer height: 0.4 mm, Perimeters: 2, Top/bottom solid layers: 3, Fill density: 20%, Fill pattern: Honeycomb, Fan speed: [35, 100], No support material
 +
File:C1072-1.png|C1072-1, FDM-3Dprinted, Material: ABS, Layer height: 0.4 mm, Perimeters: 2, Top/bottom solid layers: 3, Fill density: 20%, Fill pattern: Honeycomb, Fan speed: [35, 100], No support material
 +
File:C1083-1.png|C1083-1, FDM-3Dprinted, Material: ABS, Layer height: 0.4 mm, Perimeters: 2, Top/bottom solid layers: 3, Fill density: 20%, Fill pattern: Honeycomb, Fan speed: [35, 100], No support material
 +
File:C1080-3 2.png|C1080-3, Cover Box bottom part, galvanized steel sheet, thickness 0.5mm
 +
File:C1081-3 2.png|C1081-3, Cover Box top part, galvanized steel sheet, thickness 0.5mm
 +
File:C1082-5.png|C1082-5, Cover Box side part, galvanized steel sheet, thickness 0.5mm
 +
File:C1084-1.png|C1084-1, FDM-3Dprinted, Material: ABS, Layer height: 0.4 mm, Perimeters: 2, Top/bottom solid layers: 3, Fill density: 20%, Fill pattern: Honeycomb, Fan speed: [35, 100], No support material
 +
</gallery>
 +
 
 +
====Assembly====
 +
Follow the [https://ohai.satnogs.org/project/satnogs-rotator-v3-mechanical-assembly/ instructions for mechanical assembly] and also you can [https://www.youtube.com/watch?v=D6P9HK23Gmo watch timelapse]
 +
Also, exploded views and instructions are present here.
 +
 
 +
{{Message|
 +
Prior to Step 8, the rotary encoders must be ready and prior to Step 11 the motor must be mounted in A1070-1. For the rotary encoder assembly look at the next section [https://wiki.satnogs.org/SatNOGS_Rotator_v3#Rotator_Controller Rotator_Controller].}}
 +
 
 +
Some notes for assembly:
 +
 
 +
*Resolve collision between of end-stop arm and C1042-1 end-stop mount, [https://community.libre.space/t/rotator-3-1-end-stop-switch-mounting/3463 community post]
 +
*[https://community.libre.space/t/rotator-3-1-worm-gear-issues/1858/7 Running the worm gear] and [https://community.libre.space/t/rotator-3-1-worm-gear-issues/1858/9 lapping the worm gear] to get gear box running smooth
 +
*[https://community.libre.space/t/stepper-motor-bolts-v3-1/3388 Collision between bolts and motor], this issue can be created by using wrong M4 screws(H1100-5) and washers(H1110-1)
 +
 
 +
<gallery widths="180" heights="180" perrow="4">
 +
File:A1010-1.png|Step 1, Prepare the assembly of worm gear
 +
File:A1011.png|Step 2, Prepare the assembly of worm gear mount, 2 variants -1 and -2 (mirror)
 +
File:A1020-1.png|Step 3, Prepare the assembly of shaft collar for worm wheel
 +
File:A1033-1.png|Step 4, Prepare the encoder gear
 +
File:A1070-1.png|Step 5, Prepare the Motor mount
 +
File:A1060-1.png|Step 6, In case of DC motor configuration
 +
File:A1031-1.png|Step 7, Bearing side without encoder and end-stop mounts
 +
File:A1032-1.png|Step 8, Bearing side with encoder and end-stop mounts
 +
File:A1030.png|Step 9, Prepare symmetric and asymmetric axis, 2 variants -1 and -3
 +
File:A1001-3.png|Step 10, Frame with worm gear mount and A1001-1 assembly
 +
File:A1040.png|Step 11, Rotator module 2 Variants -1 and -3, symmetric and asymetric  [[:File:Tip for Step 11 (A1040) -- Note 10 - use of M5 Nuts to attach Drill.jpg|(Assembly Tip - Note 10:Jam two M5 nuts together at end of shaft to easily run gearbox manually)]]
 +
File:A1050-1.png|Step 12, Final step of Antenna Rotator
 +
</gallery>
 +
 
 +
====Rotator Controller====
 +
The default way of controlling the rotator is to use the [[SatNOGS Rotator Controller]].This works for both stepper motor and DC motor set ups (Note: If you are uing the [https://wiki.satnogs.org/SatNOGS_Rotator_Controller#Encoders the rotary encoders] these will need to be set up). An alternative is to use the [[SatNOGS_Arduino_Uno/CNC_Shield_Based_Rotator_Controller]], whih has been used as a stand alone set up for use with GPredict.
 +
 
 +
It's also possible to use a standard 3d printing RAMPs 1.4 board as an alternative, though note that these are designed for steppers which may cause extra RF noise. A RAMPs 1.4 [https://github.com/TheSkorm/satnogs-rotator-ramps14 firmware] has been developed.
 +
 
 +
====Cover Box - Cabling====
 +
Prepare the cover box and install it to antenna rotator with rotator controller and cables.
 +
 
 +
<gallery widths="200" heights="200" perrow="4">
 +
File:Cover_box_1.JPG| Put the C1080-3 with screws M4 L10 DIN912, C1084-1 and washers M4 DIN125 to the azimuth module. The screw with the Phillips Rounded Head Screws For Sheet Metal, M3,5 X 6,5, DIN 7981,INOX A2, C1082-5 to the C1080-3 and put the C1083-1. Note screw only the middle screw.
 +
File:Power_cable_1.JPG| The power - data cable must be passed inside the azimuth axis. This solution is tested [https://network.satnogs.org/stations/200/ in station 200] without problem.
 +
File:Power_cable_2.JPG| In the other side of power cable must be installed a connector with  4 terminals and waterproof like [https://grobotronics.com/connector-sp-4-pin-male.html Weipu - SP1310/P4I]. Also it is needed to have the female connector for cable that connected to the client. For cheaper solution use a bigger cable to connect the rotator with client and power source.
 +
File:Other_cables_2.JPG|The 3 CAT5e UTP cables are 2x sensors (encoders - end stops) 1x power and data (RS-485). For color code use [https://en.wikipedia.org/wiki/Power_over_Ethernet#Pinouts 802.3af Standards A and B] from the power sourcing equipment perspective.
 +
File:Other_cables_3.JPG|The other cables are for DC motor or stepper motors. In each side of the CAT5e UTP cables must be put a Heat-shrinkable asreferred in [https://gitlab.com/librespacefoundation/satnogs/satnogs-rotator/blob/master/rotator-bom.ods BOM]. Also a Heat-shrinkable must be putin the cable gland in rotator controller for motor cables.
 +
File:Other_cables_1.JPG|Pass all the cables though the hole in the bottom of C1080-3
 +
File:Motor_ferrite_bead.JPG|Add ferrite beads for motor cables, dimensions L25mm and OD 13mm
 +
File:Velcro_for_controller_1.JPG|Add velcro to mount the rotator controller outside the box. Velcro tape specifications: Heavy duty, stick on, max 7Kg, 50mm x 100mm. The tape might be used to mount [https://wiki.satnogs.org/No_rotator client box]  in the rotator.
 +
File:Rotator_controller_1.JPG| Cabling management inside the rotator controller. The controller is mounted to the rotator by using a tape as mentioned previously.
 +
File:Rotator controller 2.JPG| Cabling management outside the rotator controller
 +
File:Testing_1.JPG| The rotator is ready for testing, before the final step do not put the C1081-3, in order to most of components must be accessible
 +
File:Testing 2.JPG| The final step. If everything is working properly, must be put the C1081-3 by using sheet metal screws as mentioned previously. In this step if the holes of C1081-3 are not aligned with the holes of the other two parts, C1082-5 and C1080-3, drill new holes and screw them, take a look in [https://gitlab.com/librespacefoundation/satnogs/satnogs-rotator/issues/73 issue 73]. Put stickers!!!!!!
 +
 
 +
 
 +
</gallery>
 +
 
 +
====Testing====
 +
You are ready! Proceed with [https://wiki.satnogs.org/SatNOGS_Rotator_Controller#Troubleshooting_hints testing].
 +
 
 +
====Heading Calibration====
 +
The heading calibration is a manual process:
 +
 
 +
*Power the rotator, it starts moving in order to find the home position, to find the end-stops
 +
*Remove the power from the rotator, the rotator is in home position
 +
*Install the rotator to vertical axis by using U-Bolt clamps
 +
*The azimuth axis it must be heading to the North, this is achieved by using a compass (e.g. from smart phone)
 +
*Secure the rotator in the vertical axis
 +
*Install the elevation axis with the same process, now the zero elevation is achieved by using a pocket level
 +
*Secure the elevation axis
 +
*In the case of wrong rotation:
 +
**For stepper motors swap a pair of two stepper motor cables ([https://gitlab.com/librespacefoundation/satnogs/satnogs-rotator-firmware/issues/15 it exists an open issue to be done by a command])
 +
**For DC motors, [https://gitlab.com/librespacefoundation/satnogs/satnogs-rotator-firmware/commit/961fb696536e35642f2b7064cc3c64676ebebb17 change the sign of encoder reading], it is a hacky method but it would be resolved by [https://gitlab.com/librespacefoundation/satnogs/satnogs-rotator-firmware/issues/15 this issue]
 +
 
 +
====Counterweight for Antenna====
 +
It is necessary to balance the antenna in elevation and azimuth axis in order to not wear the gear box of rotator. In elevation axis would be done either by using back mounted antennas or by mounting the center of antenna mass in the mast. For a back mounted antenna, it is necessary to use counter-balance weights. An idea is to use weights that is used for training (it's cheap). The parts that used to mount weights to [https://www.wimo.com/en/x-quad X-quad antenna] are this [https://gitlab.com/librespacefoundation/satnogs/satnogs-hardware-misc/-/tree/master/mount-counterweight 3D printing part], a square aluminum profile 15x15 mm, weights with inner hole D28mm and M5 hex nuts DIN934 with M5 screws DIN912 L12 stainless steel to lock the weights in specific distance. Another way to [https://community.libre.space/t/quartapounds-satnogs-rotator-v3-1/3453/57 balance the antenna].
 +
 
 +
[[File:Counter-weight.jpg|thumb|center|800x420px|alt=|Counterweights]]
 +
 
 +
==Mechanical Analysis [WIP]==
 +
 
 +
====Brake Torque====
 +
The greatest force the tracker needs to withstand is the force created by strong wind. The worst case is when one antenna is elevated at 90 degs, facing the direction of the wind. We based our calculations on an [http://k7nv.com/notebook/topics/windload.html article] found online after comparing it to others. We “translated” the second table in metric (because we don’t understand imperial and because we needed same units system in our calculations)
 +
 
 +
{| class="wikitable"
 +
|-
 +
!Method
 +
!Wind Zone(km/h)
 +
!Height (m)
 +
!Pressure(N/m^2)
 +
|-
 +
|EIA-222-C
 +
|160
 +
|N/A
 +
|1280
 +
 
 +
|-
 +
|EIA-222-F
 +
|128
 +
|14
 +
|1260
 +
 
 +
|-
 +
|EIA-222-F
 +
|128
 +
|21
 +
|1390
 +
 
 +
|-
 +
|EIA-222-F
 +
|128
 +
|30
 +
|1500
 +
 
 +
|-
 +
|UBC'97
 +
|128
 +
|14
 +
|1290
 +
 
 +
|-
 +
|UBC'97
 +
|128
 +
|21
 +
|1160
 +
 
 +
|-
 +
|UBC'97
 +
|128
 +
|21
 +
|1390
 +
 
 +
|-
 +
|UBC'97
 +
|128
 +
|30
 +
|1260
 +
 
 +
|-
 +
|UBC'97
 +
|128
 +
|42
 +
|990
 +
 
 +
|-
 +
|UBC'97
 +
|128
 +
|42
 +
|1360
 +
 
 +
|-
 +
|Generic Formula
 +
|150
 +
|N/A
 +
|1270
 +
 
 +
|}
 +
 
 +
and we applied the worst case model (EIA-222-F) in 3 different antennas: in the biggest one of our designs, and in two others, for which we obtained data from [http://download.qrz.ru/pub/hamradio/antenna/rotators/G-800SA_1000SA.pdf yaesu G800 rotator manual at page 3]. We assumed that antennas are mounted in 1m away from the azimuth axis. For our antenna with 2m length (actual, not wavelength), made by 2cm square tube, the generated torque was ≈600Kg*cm. For the 144MHz 10-elements Yagi from the article is ≈6000Kg*cm and for the third 430MHz, 12-elements Yagi is ≈1800Kg*cm
 +
 
 +
 
 +
====Moment of inertia====
 +
Now for the moment of inertia: (for all installation methods we assumed that antennas are counterbalanced in the elevation axis) the worst case scenario here is to use two 3kg (our designs are less than 1kg) back mounted yagis with 3kg counterbalances both mounted in 0.75m away from azimuth axis. The torque you need in order to accelerate this system from ω=0deg/s angular velocity to ω=5deg/s (the math about angular velocity is below) in one second is about 60kg*cm.
 +
 
 +
Note: we suppose that the mass of antennas is near to the altitude axis, so the torque of this axis that is needed to accelerate is approximately 0.
 +
 
 +
*M1: torque of Azimuth axis
 +
*L: length of center of mass of antennas from azimuth axis (0.75m)
 +
*m: mass of antennas and of counterweight (3kg + 3kg = 6kg)
 +
*I: moment inertia
 +
*a: angular acceleration of azimuth axis 5deg/s^2
 +
*I = I1 + I2 = m*L^2 + m*L^2 = 2*m*L^2 = 6.75 kg*m^2
 +
*M1 = I*a = 6.75kgm^2 * 0.087rad/s^2 = 0.58 Nm = 5.8 kgm = 58 kgcm
 +
 
 +
 
 +
====Angular velocity====
 +
(How well do you remember trigonometry?)For the angular velocity max needed in altitude axis the things are straightforward. The closer is the satellite the larger the velocity. According to the wikipedia article about LEO, the lowest height limit is 160 km and the speed unit to orbit earth in this altitude is 7,8 km/s. As a result, maximum velocity in ALT axis is 2,8 deg/s. In ALT AZ rotator design there is a well known limitation: the closer something passes near zenith the biggest gets the velocity of the AZ axis. Therefore, we have analyzed this problem to figure out the optimal velocity and how high we are allowed to track a target in relation to AZ velocity. The picture below illustrates a ground station B which tracks a satellite Γ in X degrees altitude. The satellite velocity at this point is vertical to the screen (page) plane.
 +
 
 +
[[File:Anglular_velocity.png|thumb|center|800x420px|alt=|Angular Velocity]]
 +
 
 +
The equations that lead to maximum altitude at which we can track in relation to AZ angular velocity are
 +
 
 +
*ω : angular velocity of AZ DOF in rad/s
 +
*H = ΑΕ + ΕΓ : Minimum Height of LEO, 160 km
 +
*R = ΑΕ : Radius of Earth, 6500 km
 +
*u : linear velocity of satellite that rotates in 160km height is 7.8 km/s
 +
*ΒΔ = u / ω : ΒΔ in km
 +
*α = atan(ΒΔ / R)
 +
*δ = π - α
 +
*γ = asin( sqrt(R^2+ΒΔ^2) * sin(δ) / (H+R) )
 +
*ά = π - δ - γ
 +
*ΓΔ = (H+R) * sin(ά) / sin(δ)
 +
*χ = atan(ΓΔ / ΒΔ)
 +
 
 +
Below you can see the plot of the equations mentioned above, where horizontal axis represents angular velocity (ω) in deg/s and vertical axis shows the max track altitude (χ) for lower bound of LEO.
 +
 
 +
[[File:Anglular_velocity_plot.png|thumb|center|800x420px|alt=|Angular Velocity Plot]]
 +
 
 +
After studying this diagram, we came up to the conclusion that an angular velocity of 5 deg/s is adequate. For this decision, we took into consideration the main lobe of antenna (Δ3db) which in most situations is about 20 deg.
 +
 
 +
====Pulleys/Belts/Gearing====
 +
Horizontal distance between pulleys (P1, P2) is 58mm.
 +
Vertical distance between pulleys (P1, P2) is w = 9.5mm.
 +
 
 +
Pulleys and Belt are GT2, 2mm pitch.
 +
Belt width, 6mm.
 +
Belt thickness, 1.38mm (0.76 tooth).
 +
 
 +
Wrap angle in both pulleys is larger than 60deg.
 +
At least 6 teeth in contact with the pulley at any given time.
 +
In practice that means you want a minimum of a 12 tooth pulley, and usually try to get at least 18 teeth.
 +
 
 +
Outer Diameter of pulleys:
 +
 
 +
P(T) | OD(mm) <br />
 +
16  | 10.2 <br />
 +
20  | 12.7 <br />
 +
36  | 22.9 <br />
 +
40  | 25.5 <br />
 +
 
 +
Belt calculation (according to calculator):
 +
 
 +
Ratio    | P1(T)  | P2(T)  | Belt(T) | L(mm)  <br />
 +
2.25|16|36|85/86|58.65/59.66  <br />
 +
1.8|20|36|86/87/88|57.78/58.78/59.78  <br />
 +
2.5|16|40|87/88|58.5/59.5 <br />
 +
2|20|40|89/90|58.65/59.66 <br />
 +
 
 +
Motor Maximun no-load speed, 200RPM = 1200deg/s
 +
Motor Maximum stall-torue, 1.2Nm
 +
 
 +
[[File:Motor_perfomance_graph.png|thumb|center|800x420px|alt=|Angular Velocity]]
 +
 
 +
Position of idler do not care, or min 1.3*P1, max 1.5*P1 (for 20T, ~16mm/~20mm).
 +
 
 +
Belt gear selection:
 +
 
 +
*20/36 with 1.8 ratio and 86T/172mm belt without idler
 +
*20/40 with 2 ratio and 90T/190mm belt with idler
 +
 
 +
To calculate Deflection force, (page T-31, sdp - design-guidelines)
 +
 
 +
*Y = 2.05, Tst = 1.3kg
 +
*span length, t = 57.64mm
 +
*Belt pitch length, L = 180mm
 +
*Fd,min =
 +
*Fd,max =
 +
*2.8kg Working Tension [shapeoko - Belts and Pulleys](https://www.shapeoko.com/wiki/index.php/Belts_and_Pulleys#Tensile_Cord_Materials)
 +
 
 +
 
 +
  P3  <br />
 +
  /  \  <br />
 +
P1  P2  <br />
 +
    |  <br />
 +
    P4-P5  <br />
 +
 
 +
*Determination of design load
 +
 
 +
According to perfomance graph of DC motor, the optimal output power is Tm = 0.6Nm  with efficiency of 0.2 and 100RPM = 600deg/s.
 +
Select a service factor of 1.5 (service factors between 1.5 and 2.0 are generally recommended when
 +
designing small pitch synchronous drives).
 +
Tpeak = SF*Tm = 1.5*0.6 = 0.9Nm
 +
 
 +
*Choice of belt pitch
 +
 
 +
Due to backslash and accuracy in both directions of movements and volume constrains, we choose GT2, pitch 2mm.
 +
 
 +
*Check belt pitch selection based on individual graphs
 +
 
 +
Due to Tpeak = 0.9Nm No-load speed,(Speed of fastest shaft) = 100RPM = 600deg/s
 +
GT2 pitch 2mm belt is the better solution for our application.
 +
 
 +
*Determine speed ratio
 +
 
 +
Speed ratio 1.8-2.25 according to specification of output rotation speed of 5deg/s.
 +
 
 +
*Check belt speed
 +
 
 +
V(m/s) = 0.0000524 x pulley PD (mm) x pulley rpm = 0.066548m/s
 +
Belt speeds up to 6,500 fpm (33.02 m/s) do not require special pulleys.
 +
 
 +
*Determine belt length
 +
 
 +
Table 'Belt calculation (according to calculator)'
 +
Teeth in mesh: 9
 +
 
 +
*Determine the belt width
 +
 
 +
From Table 43
 +
torque = 0.17Nm
 +
Length Correction Factor = 0.9
 +
width multiplier = 1.00
 +
torque*Length Correction Factor*width multiplier = 0.17*0.9*1.00 = 0.153Nm
 +
Teeth in mesh: 9
 +
Tpeak = 0.9Nm, so belt width is nice for our application
 +
 
 +
*Check the number of teeth in mesh
 +
 
 +
Teeth in mesh: 9 according to calculator
 +
 
 +
*Determine proper belt installation tension
 +
 
 +
SECTION 10, on page T50, look at 'To calculate Deflection force, (page T-31, sdp - design-guidelines)'
 +
 
 +
*Y = 2.05, Tst = 0.812*DQ/d + mS^2 = 12.8lb + 0 = 5.8kg
 +
*DQ = Tpeak = 0.9Nm = 7.9lb-in
 +
*d = 12.7mm = 0.5in
 +
*S = (0.5*100/3.82)/1000 = 0.0131ft/min
 +
*m = 0.039
 +
*span length, t = sqrt(CD^2 - (PD-pd/2)^2) = 57.64mm
 +
*Belt pitch length, L = 180mm
 +
*t/L = 0.32
 +
*Fd,min = 0.8lb = 0.36kg
 +
*Fd,max = 0.9lb = 0.41kg
 +
 
 +
*Safety factor 1.5
 +
 
 +
*P2 timing pulley torque - Maximum radial load of timing belt ball bearing 625zz
 +
 
 +
Tpeak = 0.9Nm
 +
TorqueP2 = 2*0.9Nm = 1.8Nm, PDp2 = 25.5mm
 +
Radial static load of 625ZZ is 0.38kN
 +
T-39
 +
 
 +
*Maximum thrust load of timing belt ball bearing 625zz
 +
 
 +
*Maximum radial and thrust load of output ball bearings 6008zz
 +
 
 +
Calculate or evaluate correct loads for deep groove ball bearings
 +
radial static load = 11.6kN
 +
thrust static load = 0.7*11.6kN = 8.12kN
 +
This type of construction permits the bearings to support relatively high thrust load in either direction.
 +
In fact the thrust load capacity is about 70% of the radial load capacity. A ball bearing primarily  designed
 +
to support radial load can also support high thrust load; because only few balls carry the radial load,
 +
whereas all the balls can withstand the thrust load.
 +
 
 +
*Maximum self-locking or back-drivable torque of gear box (according to more weak component)
 +
 
 +
It necessary to achieve [specs](https://community.libre.space/t/satnogs-rotator-version-3/226), 60Nm (6Kg in 1 meter)
 +
 
 +
*Nominal torque of drivable torque of gear box (according to more weak component) and maximum rotational speed of gear box
 +
 
 +
Notes:
 +
 
 +
*[https://sdp-si.com/eStore/CenterDistanceDesigner sdp distance calculator]
 +
*[http://www.ebay.com/itm/2GT-Timing-Belt-L-172-232-240-244-640-810-GT2-Belts-closed-loop-5pcs-lot-/221977955532?var=&hash=item33aeeacccc:m:me5GvSt_amrm6RWT03Ut4JA belt GT2-6mm wide, 172mm]
 +
*[https://www.ebay.com/itm/2GT-GT2-synchronous-Timing-belt-Perimeter-98-194mm-width-6-9mm-Cogged-close-loop/222574382655?ssPageName=STRK%3AMEBIDX%3AIT&var=521434616407&_trksid=p2060353.m2749.l2649 belt GT2-6mm wide, 180mm]
 +
*[http://www.ebay.com/itm/5pcs-Timing-Pulley-GT2-Idler-16-20T-gear-Bearing-Reprap-6mm-Belt-3-5mm-Bore-3D-/132195520937?var=&hash=item1ec77791a9:m:mljSYBViBlKOgXr3Gy-u0Tg idler pulley, no-teeth-ID3mm-OD18mm]
 +
*[http://www.brecoflex.com/products/pulleys/design-guidelines/ brecoflex - design-guidelines]
 +
*[http://www.shreegeeimpex.com/TECH_DATA_PAG/idlers_ten.htm shreegeeimpex - design-guidelines]
 +
*[http://www.sdp-si.com/PDFS/Technical-Section-Timing.pdf sdp - design-guidelines]
 +
 
 +
====Motor Specification====
 +
 
 +
General Specification about motors. The voltage and current consumption also it depends from the motor controller which is (maybe) different
 +
from [https://wiki.satnogs.org/SatNOGS_Rotator_Controller SatNOGS Rotator Controller].
 +
 
 +
{| class="wikitable"
 +
|-
 +
!Specification
 +
!Value
 +
|-
 +
|Min-Max Stall Torque (Nm)
 +
|0.4 - 1.5
 +
|-
 +
|Min-Max Speed (RPM)
 +
|100 - 200
 +
|-
 +
|Size (mm) (LxWxH)
 +
|47x42x64
 +
|-
 +
|}
 +
 
 +
<gallery widths="200" heights="200" perrow="4">
 +
File:Motor mount dimensions.png|Motor mount dimensions
 +
File:Max motor height.png|Maximum Motor Height
 +
</gallery>
 +
 
 +
====Worm Gear Box Calculations====
 +
 
 +
*Gear ratio: i12 = 30
 +
*Angle between axis of gears: δ = 90 deg
 +
*Number of threads in worm: If i12 >= 30 then z1 = 1
 +
*Number of teeth in worm wheel: z2 = i12*z1 = 30
 +
*Center distance: initial case a = 45.5 mm
 +
*Worm reference diameter: AGMA d01>= 11.5*(a/25.4)^0.875 = 19.15 mm, so d01 = 19.5mm
 +
*Worm wheel reference: d02 = 2*a - d01 = 71.5 mm
 +
*Axial module: ms = d02/z2 = 2.38 , so ms = 2.5
 +
 
 +
Recalculate d02, a with new axial module
 +
 
 +
*d02 = z2*ms = 75mm, a = (d02+d01)/2 = 47.25mm
 +
*Axial pitch: ts = π*ms = 7.854mm
 +
*Reference lead angle: γ0 = atan(d02/(i12*d01)) = 7.3 deg
 +
*Worm tip diameter: dk1 = d01 + 2*hk = 24.5mm
 +
**Worm teeth reference addendum in axial section: hk = hk* *ms = 2.5mm
 +
**Worm tooth reference addendum coefficient: hk* = 1
 +
*Worm root diameter: df1 = d01 - 2*hf = 13.5mm
 +
**Worm tooth reference dedendum: hf = hf* _ms = 1.2_ms = 3mm
 +
**Dedendum coefficient: hf* = 1.2
 +
*Worm length: L = 2.5_ms_sqrt(z2+2) = 35.36mm
 +
*Worm tooth thickness: smx1 = smx1* * ts = 3.927mm
 +
**Tooth thickness coefficient: smx1* = 0.5
 +
*Normal pressure angle: aon = 20 deg
 +
*Worm wheel throat diameter: dk2 = d02+2*hk = 80mm
 +
*Worm wheel root diameter: df2 = d02 - 2*hf = 69mm
 +
*Worm wheel outside diameter: de2 = dk2 + 2*mx = 83.5mm
 +
**Worm wheel tooth external addendum: mx = n*ms, 0.4<=n<=1.5
 +
*Effective worm wheel face width: b2H,max = sqrt((2_a - df2)^2 - (2_a - de2)^2) = 23mm
 +
 
 +
[[Category:Build]]
 +
[[Category:Hardware]]
 +
[[Category:Rotator]]

Latest revision as of 06:38, 8 September 2022

SatNOGS Rotator v3
SatNOGS Rotator v3
Rotator Information
Type: Az/El
Cost: ~220 USD
Release Information
Status: Beta
Latest Release: v3.1-pre-release
Repository: [1]
Documentation: [v3.0.1 v3.1]
 


Introduction

v3 marks a major re-haul of the SatNOGS Rotator design, with learnings from v2 applied. You can see a lot of the thinking and background research that was conducted prior to v3 development in this thread. Also in this wiki page you can also find a "How to build the rotator", mechanical analysis and all documentation about the SatNOGS rotator.

Also in this list is presented different rotators, either commercial or DIY builds.

Specifications

SatNOGS v3 Rotator
Plastic Parts 15
Non Printed Parts 38
Cost ~ $220
Controller Electronics SatNOGS Rotator Controller
Type AZ/EL (possible X/Y)
Motors 2x NEMA 17 Stepper or 2x DC Motors
Frame Material Aluminum T-slot 20x20
Speed (deg/sec) 7
Torque (Nm) ?, ~30
Brake Torque (Nm) ?
Dimensions (mm) 280x140x140 (AZ/EL)
Weight (kg) ~5

Design Goals

Considering the specifications as detailed in the Mechanical Analysis, we would also like for the 3rd version of SatNOGS rotator to be:

  • inexpensive (less than €300, if possible)
  • lightweight and portable (~6Kg, size:~300x~150x~150mm)
  • rigid and durable
  • easy to build and fix (try to use easily available materials)
  • weatherproof
  • electromagnetically shielded, so that noise in reception is reduced
  • accurate (<1deg, backlash reduction and use of encoders at the axis)

Sourcing

3d Printing at a Fab Lab or your local hackerspace: If you don't have your own 3d printer, then a local Fab Lab or hackerspace may be able to do it for you. Fab Labs and hackerspaces are places that have invested in the machinery and you can take the designs to them. Generally they need .stl files to import into the software that runs the machines, but this should be discussed with the Fab Lab or hackerspace. You then pay for the material, time or a combination of the two for each of the parts or any other agreement in place.

Most people building the rotator have had success builds with simple ABS material for the 3D printing parts.

T Slot - If you don't want to cut the pieces yourself, then you may be able to find a supplier that will do this for you. (Here's one in the United Kingdom.)

Hidden corner connectors - AliExpress gave the cheapest supplier

A good US source is MISUMI-USA; they will also cut to length. MISUMI has several other global locations [2].

Beware, the 20-series T-slot from 80/20 Inc. in the US has slots that are only 5.2mm wide. The hidden corner connectors from e.g. AliExpress will not fit.

Stepper Motors - eBay

Belts - eBay

Fixings / Pipe - eBay

Vendors Table

Like the RepRap Buyers' Guide wiki, feel free to populate the table.

Vendor Location Parts Notes
pololu USA, Worldwide Motors, electronics -
mouser Worldwide Motors, electronics -
ebay Worldwide Motors, electronics, Fasteners, T-Slots, pulleys, Tubes -
aliexpress Worldwide Motors, electronics, Fasteners, T-Slots, pulleys, Tubes -
grobotronics GR, EU Motors, electronics, Fasteners, T-Slots, pulleys -
motedis DE, EU T-Slots, Tubes -
Misumi Worldwide T-Slots, Tubes, Fasteners, Pulleys -
omc-stepperonline Worldwide Stepper motors -
fastenal USA Fasteners -
mcmaster USA Fasteners -
rs Worldwide Electronics, fasteners, motors -
80/20 USA T-Slots -
pcbway CN PCB fabrication -
servocity USA Motors, T-slots, fasteners Most of parts are not metric

Build Sequence

Tools & Consumables

Here are presented tools and consumables about part fabrication, port-processing and assembly process. Most of the tools are available in every hackerspace, makerspaces, FabLabs etc.

Tool/Consumable Description
Drill bits 2mm for aluminum, 3mm, 4mm and 5mm for plastic
Drill driver For aluminum tube drill hole, 3D printed part
Sandpaper 80(dry), 120(dry), 240(dry) and 1000(wet) grit
Acetone For acetone vapor bath
Hacksaw For aluminum Tube
Square File For worm axis, for use on steel
Precision Knife For general use, especially in 3d-Printed parts
Caliper Measuring Range 0-150mm
Combination Wrenches 5.5mm, 7mm and 8mm
Thread-locker Like Loctite 271
Cyano acrylic glue Like Loctite 401
Screw driver Number 1 Phillips
Heat Gun For Heat-shrinkables or use a lighter
Ball-End L-Keys Hex 1.5mm, 2mm, 2.5mm, and 3mm
Soldering iron and consumables For cables
Wire Cutter For cables
Long-Nose Plier General purpose

Parts

Make sure you have all parts, according to BOM.

Most of the parts could be fabricated by a FDM 3D-printer. Some parts have only 2D geometry so could be fabricated by a laser cutter. Other parts have modifications of common(hardware) parts like threaded rods or aluminum pipes. Also you could find a lot of guides for post processing for FDM printed parts.

  • C1001, Aluminum Tube 6063 OD40mm TH1.5mm L240mm, 2 variants -1 and -3

  • C1010-3, FDM-3Dprinted, Material: ABS, Layer height: 0.4 mm, Perimeters: 2, Top/bottom solid layers: 3, Fill density: 20%, Fill pattern: Honeycomb, Fan speed: [35, 100], No support material

  • C1011-3, laser cut in 3mm Acrylic Sheet or in FDM-3Dprinter with same fabrication parameters as C1010-3

  • C1020-1, FDM-3Dprinted, Material: ABS, Layer height: 0.4 mm, Perimeters: 2, Top/bottom solid layers: 3, Fill density: 20%, Fill pattern: Honeycomb, Fan speed: [35, 100], No support material, Smoothing the part with acetone vapor bath

  • C1021-1, FDM-3Dprinted, Material: ABS, Layer height: 0.4 mm, Perimeters: 2, Top/bottom solid layers: 3, Fill density: 20%, Fill pattern: Honeycomb, Fan speed: [35, 100], No support material, Smoothing the part with acetone vapor bath, Imperial variant, tool that helps to build imperial part

  • C1022-3, laser cut in 3mm Acrylic Sheet or in FDM-3Dprinter with same fabrication parameters as C1010-3

  • C1030-1, FDM-3Dprinted, Material: ABS, Layer height: 0.4 mm, Perimeters: 2, Top/bottom solid layers: 3, Fill density: 20%, Fill pattern: Honeycomb, Fan speed: [35, 100], No support material

  • C1040-1, FDM-3Dprinted, Material: ABS, Layer height: 0.4 mm, Perimeters: 2, Top/bottom solid layers: 3, Fill density: 20%, Fill pattern: Honeycomb, Fan speed: [35, 100], No support material, Imperial variant, tool that helps to build imperial part

  • C1041-1, FDM-3Dprinted, Material: ABS, Layer height: 0.4 mm, Perimeters: 2, Top/bottom solid layers: 3, Fill density: 20%, Fill pattern: Honeycomb, Fan speed: [35, 100], No support material, Imperial variant, tool that helps to build imperial part

  • C1042-1, laser cut in 3mm Acrylic Sheet or in FDM-3Dprinter with same fabrication parameters as C1010-3

  • C1043-1, FDM-3Dprinted, Material: ABS, Layer height: 0.4 mm, Perimeters: 2, Top/bottom solid layers: 3, Fill density: 20%, Fill pattern: Honeycomb, Fan speed: [35, 100], Support material, Brim Width: 2 mm

  • C1050, Aluminum Profile 20x20 B-type slot 6, 2 variants -1 and -5

  • C1060-1, M5 Threaded rod A2 stainless steel(304)

  • C1061, 2 variants -5 and -6, FDM-3Dprinted, Material: ABS, Layer height: 0.4 mm, Perimeters: 2, Top/bottom solid layers: 3, Fill density: 20%, Fill pattern: Honeycomb, Fan speed: [35, 100], No support material

  • C1062-1, It is recommended to build in laser sintering like Shapeways with White Versatile Plastic (cost ~10€) or like C1030-1 and Smoothing the part with acetone vapor bath

  • C1070-1, FDM-3Dprinted, Material: ABS, Layer height: 0.4 mm, Perimeters: 2, Top/bottom solid layers: 3, Fill density: 20%, Fill pattern: Honeycomb, Fan speed: [35, 100], No support material

  • C1071-1, FDM-3Dprinted, Material: ABS, Layer height: 0.4 mm, Perimeters: 2, Top/bottom solid layers: 3, Fill density: 20%, Fill pattern: Honeycomb, Fan speed: [35, 100], No support material

  • C1072-1, FDM-3Dprinted, Material: ABS, Layer height: 0.4 mm, Perimeters: 2, Top/bottom solid layers: 3, Fill density: 20%, Fill pattern: Honeycomb, Fan speed: [35, 100], No support material

  • C1083-1, FDM-3Dprinted, Material: ABS, Layer height: 0.4 mm, Perimeters: 2, Top/bottom solid layers: 3, Fill density: 20%, Fill pattern: Honeycomb, Fan speed: [35, 100], No support material

  • C1080-3, Cover Box bottom part, galvanized steel sheet, thickness 0.5mm

  • C1081-3, Cover Box top part, galvanized steel sheet, thickness 0.5mm

  • C1082-5, Cover Box side part, galvanized steel sheet, thickness 0.5mm

  • C1084-1, FDM-3Dprinted, Material: ABS, Layer height: 0.4 mm, Perimeters: 2, Top/bottom solid layers: 3, Fill density: 20%, Fill pattern: Honeycomb, Fan speed: [35, 100], No support material

Assembly

Follow the instructions for mechanical assembly and also you can watch timelapse Also, exploded views and instructions are present here.

Idea.png
Prior to Step 8, the rotary encoders must be ready and prior to Step 11 the motor must be mounted in A1070-1. For the rotary encoder assembly look at the next section Rotator_Controller.

Some notes for assembly:

  • Step 1, Prepare the assembly of worm gear

  • Step 2, Prepare the assembly of worm gear mount, 2 variants -1 and -2 (mirror)

  • Step 3, Prepare the assembly of shaft collar for worm wheel

  • Step 4, Prepare the encoder gear

  • Step 5, Prepare the Motor mount

  • Step 6, In case of DC motor configuration

  • Step 7, Bearing side without encoder and end-stop mounts

  • Step 8, Bearing side with encoder and end-stop mounts

  • Step 9, Prepare symmetric and asymmetric axis, 2 variants -1 and -3

  • Step 10, Frame with worm gear mount and A1001-1 assembly

  • Step 11, Rotator module 2 Variants -1 and -3, symmetric and asymetric (Assembly Tip - Note 10:Jam two M5 nuts together at end of shaft to easily run gearbox manually)

  • Step 12, Final step of Antenna Rotator

Rotator Controller

The default way of controlling the rotator is to use the SatNOGS Rotator Controller.This works for both stepper motor and DC motor set ups (Note: If you are uing the the rotary encoders these will need to be set up). An alternative is to use the SatNOGS_Arduino_Uno/CNC_Shield_Based_Rotator_Controller, whih has been used as a stand alone set up for use with GPredict.

It's also possible to use a standard 3d printing RAMPs 1.4 board as an alternative, though note that these are designed for steppers which may cause extra RF noise. A RAMPs 1.4 firmware has been developed.

Cover Box - Cabling

Prepare the cover box and install it to antenna rotator with rotator controller and cables.

  • Put the C1080-3 with screws M4 L10 DIN912, C1084-1 and washers M4 DIN125 to the azimuth module. The screw with the Phillips Rounded Head Screws For Sheet Metal, M3,5 X 6,5, DIN 7981,INOX A2, C1082-5 to the C1080-3 and put the C1083-1. Note screw only the middle screw.

  • The power - data cable must be passed inside the azimuth axis. This solution is tested in station 200 without problem.

  • In the other side of power cable must be installed a connector with 4 terminals and waterproof like Weipu - SP1310/P4I. Also it is needed to have the female connector for cable that connected to the client. For cheaper solution use a bigger cable to connect the rotator with client and power source.

  • The 3 CAT5e UTP cables are 2x sensors (encoders - end stops) 1x power and data (RS-485). For color code use 802.3af Standards A and B from the power sourcing equipment perspective.

  • The other cables are for DC motor or stepper motors. In each side of the CAT5e UTP cables must be put a Heat-shrinkable asreferred in BOM. Also a Heat-shrinkable must be putin the cable gland in rotator controller for motor cables.

  • Pass all the cables though the hole in the bottom of C1080-3

  • Add ferrite beads for motor cables, dimensions L25mm and OD 13mm

  • Add velcro to mount the rotator controller outside the box. Velcro tape specifications: Heavy duty, stick on, max 7Kg, 50mm x 100mm. The tape might be used to mount client box in the rotator.

  • Cabling management inside the rotator controller. The controller is mounted to the rotator by using a tape as mentioned previously.

  • Cabling management outside the rotator controller

  • The rotator is ready for testing, before the final step do not put the C1081-3, in order to most of components must be accessible

  • The final step. If everything is working properly, must be put the C1081-3 by using sheet metal screws as mentioned previously. In this step if the holes of C1081-3 are not aligned with the holes of the other two parts, C1082-5 and C1080-3, drill new holes and screw them, take a look in issue 73. Put stickers!!!!!!

Testing

You are ready! Proceed with testing.

Heading Calibration

The heading calibration is a manual process:

  • Power the rotator, it starts moving in order to find the home position, to find the end-stops
  • Remove the power from the rotator, the rotator is in home position
  • Install the rotator to vertical axis by using U-Bolt clamps
  • The azimuth axis it must be heading to the North, this is achieved by using a compass (e.g. from smart phone)
  • Secure the rotator in the vertical axis
  • Install the elevation axis with the same process, now the zero elevation is achieved by using a pocket level
  • Secure the elevation axis
  • In the case of wrong rotation:

Counterweight for Antenna

It is necessary to balance the antenna in elevation and azimuth axis in order to not wear the gear box of rotator. In elevation axis would be done either by using back mounted antennas or by mounting the center of antenna mass in the mast. For a back mounted antenna, it is necessary to use counter-balance weights. An idea is to use weights that is used for training (it's cheap). The parts that used to mount weights to X-quad antenna are this 3D printing part, a square aluminum profile 15x15 mm, weights with inner hole D28mm and M5 hex nuts DIN934 with M5 screws DIN912 L12 stainless steel to lock the weights in specific distance. Another way to balance the antenna.

Counterweights

Mechanical Analysis [WIP]

Brake Torque

The greatest force the tracker needs to withstand is the force created by strong wind. The worst case is when one antenna is elevated at 90 degs, facing the direction of the wind. We based our calculations on an article found online after comparing it to others. We “translated” the second table in metric (because we don’t understand imperial and because we needed same units system in our calculations)

Method Wind Zone(km/h) Height (m) Pressure(N/m^2)
EIA-222-C 160 N/A 1280
EIA-222-F 128 14 1260
EIA-222-F 128 21 1390
EIA-222-F 128 30 1500
UBC'97 128 14 1290
UBC'97 128 21 1160
UBC'97 128 21 1390
UBC'97 128 30 1260
UBC'97 128 42 990
UBC'97 128 42 1360
Generic Formula 150 N/A 1270

and we applied the worst case model (EIA-222-F) in 3 different antennas: in the biggest one of our designs, and in two others, for which we obtained data from yaesu G800 rotator manual at page 3. We assumed that antennas are mounted in 1m away from the azimuth axis. For our antenna with 2m length (actual, not wavelength), made by 2cm square tube, the generated torque was ≈600Kg*cm. For the 144MHz 10-elements Yagi from the article is ≈6000Kg*cm and for the third 430MHz, 12-elements Yagi is ≈1800Kg*cm


Moment of inertia

Now for the moment of inertia: (for all installation methods we assumed that antennas are counterbalanced in the elevation axis) the worst case scenario here is to use two 3kg (our designs are less than 1kg) back mounted yagis with 3kg counterbalances both mounted in 0.75m away from azimuth axis. The torque you need in order to accelerate this system from ω=0deg/s angular velocity to ω=5deg/s (the math about angular velocity is below) in one second is about 60kg*cm.

Note: we suppose that the mass of antennas is near to the altitude axis, so the torque of this axis that is needed to accelerate is approximately 0.

  • M1: torque of Azimuth axis
  • L: length of center of mass of antennas from azimuth axis (0.75m)
  • m: mass of antennas and of counterweight (3kg + 3kg = 6kg)
  • I: moment inertia
  • a: angular acceleration of azimuth axis 5deg/s^2
  • I = I1 + I2 = m*L^2 + m*L^2 = 2*m*L^2 = 6.75 kg*m^2
  • M1 = I*a = 6.75kgm^2 * 0.087rad/s^2 = 0.58 Nm = 5.8 kgm = 58 kgcm


Angular velocity

(How well do you remember trigonometry?)For the angular velocity max needed in altitude axis the things are straightforward. The closer is the satellite the larger the velocity. According to the wikipedia article about LEO, the lowest height limit is 160 km and the speed unit to orbit earth in this altitude is 7,8 km/s. As a result, maximum velocity in ALT axis is 2,8 deg/s. In ALT AZ rotator design there is a well known limitation: the closer something passes near zenith the biggest gets the velocity of the AZ axis. Therefore, we have analyzed this problem to figure out the optimal velocity and how high we are allowed to track a target in relation to AZ velocity. The picture below illustrates a ground station B which tracks a satellite Γ in X degrees altitude. The satellite velocity at this point is vertical to the screen (page) plane.

Angular Velocity

The equations that lead to maximum altitude at which we can track in relation to AZ angular velocity are

  • ω : angular velocity of AZ DOF in rad/s
  • H = ΑΕ + ΕΓ : Minimum Height of LEO, 160 km
  • R = ΑΕ : Radius of Earth, 6500 km
  • u : linear velocity of satellite that rotates in 160km height is 7.8 km/s
  • ΒΔ = u / ω : ΒΔ in km
  • α = atan(ΒΔ / R)
  • δ = π - α
  • γ = asin( sqrt(R^2+ΒΔ^2) * sin(δ) / (H+R) )
  • ά = π - δ - γ
  • ΓΔ = (H+R) * sin(ά) / sin(δ)
  • χ = atan(ΓΔ / ΒΔ)

Below you can see the plot of the equations mentioned above, where horizontal axis represents angular velocity (ω) in deg/s and vertical axis shows the max track altitude (χ) for lower bound of LEO.

Angular Velocity Plot

After studying this diagram, we came up to the conclusion that an angular velocity of 5 deg/s is adequate. For this decision, we took into consideration the main lobe of antenna (Δ3db) which in most situations is about 20 deg.

Pulleys/Belts/Gearing

Horizontal distance between pulleys (P1, P2) is 58mm. Vertical distance between pulleys (P1, P2) is w = 9.5mm.

Pulleys and Belt are GT2, 2mm pitch. Belt width, 6mm. Belt thickness, 1.38mm (0.76 tooth).

Wrap angle in both pulleys is larger than 60deg. At least 6 teeth in contact with the pulley at any given time. In practice that means you want a minimum of a 12 tooth pulley, and usually try to get at least 18 teeth.

Outer Diameter of pulleys:

P(T) | OD(mm)
16 | 10.2
20 | 12.7
36 | 22.9
40 | 25.5

Belt calculation (according to calculator):

Ratio | P1(T) | P2(T) | Belt(T) | L(mm)
2.25|16|36|85/86|58.65/59.66
1.8|20|36|86/87/88|57.78/58.78/59.78
2.5|16|40|87/88|58.5/59.5
2|20|40|89/90|58.65/59.66

Motor Maximun no-load speed, 200RPM = 1200deg/s Motor Maximum stall-torue, 1.2Nm

Angular Velocity

Position of idler do not care, or min 1.3*P1, max 1.5*P1 (for 20T, ~16mm/~20mm).

Belt gear selection:

  • 20/36 with 1.8 ratio and 86T/172mm belt without idler
  • 20/40 with 2 ratio and 90T/190mm belt with idler

To calculate Deflection force, (page T-31, sdp - design-guidelines) 


  P3  

 /  \  

P1  P2  

    |  

    P4-P5
  • Determination of design load

According to perfomance graph of DC motor, the optimal output power is Tm = 0.6Nm with efficiency of 0.2 and 100RPM = 600deg/s. Select a service factor of 1.5 (service factors between 1.5 and 2.0 are generally recommended when designing small pitch synchronous drives). Tpeak = SF*Tm = 1.5*0.6 = 0.9Nm

  • Choice of belt pitch

Due to backslash and accuracy in both directions of movements and volume constrains, we choose GT2, pitch 2mm.

  • Check belt pitch selection based on individual graphs

Due to Tpeak = 0.9Nm No-load speed,(Speed of fastest shaft) = 100RPM = 600deg/s GT2 pitch 2mm belt is the better solution for our application.

  • Determine speed ratio

Speed ratio 1.8-2.25 according to specification of output rotation speed of 5deg/s.

  • Check belt speed

V(m/s) = 0.0000524 x pulley PD (mm) x pulley rpm = 0.066548m/s Belt speeds up to 6,500 fpm (33.02 m/s) do not require special pulleys.

  • Determine belt length

Table 'Belt calculation (according to calculator)' Teeth in mesh: 9

  • Determine the belt width

From Table 43 torque = 0.17Nm Length Correction Factor = 0.9 width multiplier = 1.00 torque*Length Correction Factor*width multiplier = 0.17*0.9*1.00 = 0.153Nm Teeth in mesh: 9 Tpeak = 0.9Nm, so belt width is nice for our application

  • Check the number of teeth in mesh

Teeth in mesh: 9 according to calculator

  • Determine proper belt installation tension

SECTION 10, on page T50, look at 'To calculate Deflection force, (page T-31, sdp - design-guidelines)'

  • Y = 2.05, Tst = 0.812*DQ/d + mS^2 = 12.8lb + 0 = 5.8kg
  • DQ = Tpeak = 0.9Nm = 7.9lb-in
  • d = 12.7mm = 0.5in
  • S = (0.5*100/3.82)/1000 = 0.0131ft/min
  • m = 0.039
  • span length, t = sqrt(CD^2 - (PD-pd/2)^2) = 57.64mm
  • Belt pitch length, L = 180mm
  • t/L = 0.32
  • Fd,min = 0.8lb = 0.36kg
  • Fd,max = 0.9lb = 0.41kg
  • Safety factor 1.5
  • P2 timing pulley torque - Maximum radial load of timing belt ball bearing 625zz

Tpeak = 0.9Nm TorqueP2 = 2*0.9Nm = 1.8Nm, PDp2 = 25.5mm Radial static load of 625ZZ is 0.38kN T-39

  • Maximum thrust load of timing belt ball bearing 625zz
  • Maximum radial and thrust load of output ball bearings 6008zz

Calculate or evaluate correct loads for deep groove ball bearings radial static load = 11.6kN thrust static load = 0.7*11.6kN = 8.12kN This type of construction permits the bearings to support relatively high thrust load in either direction. In fact the thrust load capacity is about 70% of the radial load capacity. A ball bearing primarily designed to support radial load can also support high thrust load; because only few balls carry the radial load, whereas all the balls can withstand the thrust load.

  • Maximum self-locking or back-drivable torque of gear box (according to more weak component)

It necessary to achieve [specs](https://community.libre.space/t/satnogs-rotator-version-3/226), 60Nm (6Kg in 1 meter)

  • Nominal torque of drivable torque of gear box (according to more weak component) and maximum rotational speed of gear box

Notes:

Motor Specification

General Specification about motors. The voltage and current consumption also it depends from the motor controller which is (maybe) different from SatNOGS Rotator Controller.

Specification Value
Min-Max Stall Torque (Nm) 0.4 - 1.5
Min-Max Speed (RPM) 100 - 200
Size (mm) (LxWxH) 47x42x64

  • Motor mount dimensions

  • Maximum Motor Height

Worm Gear Box Calculations

  • Gear ratio: i12 = 30
  • Angle between axis of gears: δ = 90 deg
  • Number of threads in worm: If i12 >= 30 then z1 = 1
  • Number of teeth in worm wheel: z2 = i12*z1 = 30
  • Center distance: initial case a = 45.5 mm
  • Worm reference diameter: AGMA d01>= 11.5*(a/25.4)^0.875 = 19.15 mm, so d01 = 19.5mm
  • Worm wheel reference: d02 = 2*a - d01 = 71.5 mm
  • Axial module: ms = d02/z2 = 2.38 , so ms = 2.5

Recalculate d02, a with new axial module

  • d02 = z2*ms = 75mm, a = (d02+d01)/2 = 47.25mm
  • Axial pitch: ts = π*ms = 7.854mm
  • Reference lead angle: γ0 = atan(d02/(i12*d01)) = 7.3 deg
  • Worm tip diameter: dk1 = d01 + 2*hk = 24.5mm
    • Worm teeth reference addendum in axial section: hk = hk* *ms = 2.5mm
    • Worm tooth reference addendum coefficient: hk* = 1
  • Worm root diameter: df1 = d01 - 2*hf = 13.5mm
    • Worm tooth reference dedendum: hf = hf* _ms = 1.2_ms = 3mm
    • Dedendum coefficient: hf* = 1.2
  • Worm length: L = 2.5_ms_sqrt(z2+2) = 35.36mm
  • Worm tooth thickness: smx1 = smx1* * ts = 3.927mm
    • Tooth thickness coefficient: smx1* = 0.5
  • Normal pressure angle: aon = 20 deg
  • Worm wheel throat diameter: dk2 = d02+2*hk = 80mm
  • Worm wheel root diameter: df2 = d02 - 2*hf = 69mm
  • Worm wheel outside diameter: de2 = dk2 + 2*mx = 83.5mm
    • Worm wheel tooth external addendum: mx = n*ms, 0.4<=n<=1.5
  • Effective worm wheel face width: b2H,max = sqrt((2_a - df2)^2 - (2_a - de2)^2) = 23mm
Retrieved from "https://wiki.satnogs.org/index.php?title=SatNOGS_Rotator_v3&oldid=3849"
  • Creative Commons Attribution-ShareAlike
  • Powered by MediaWiki