Difference between revisions of "SatNOGS Rotator v3"

From SatNOGS Wiki
(Sourcing)
Line 53: Line 53:
  
 
'''Fixings / Pipe''' - eBay
 
'''Fixings / Pipe''' - eBay
 
'''Antenna Hardware''' - The yagi antenna is suited to the novice builder but there are many types. Each satellite has an uplink and a downlink so it is necessary to have an antenna that will work on the downlink side for receiving and one for the uplink if you are transmitting to the satellite (Transmitting requires a licence - an amateur radio licence normally suffices fr most countries).
 
Antennas have a gain associated with them that is related to the number of elements. Simply the greater the number of elements the greate the gain, however the more directional they become and the greater accuracy is needed. So a trade off between gain and beam width is required. Nominally a 3 element beam for 145Mhz (2m band) and a 7 element beam for 432MHz (70cms band) will suffice for most applications.
 
Some satellites need a different type of antenna that has circular polarisation and these are helical to look at. The satNOGS helical design should be followed. A simple to build antenna can be sources from Nuxcomm [http://www.nuxcom.de/en]
 
 
'''Receiver''' - The RTL-SDR dongle used for the reciver is a broad band software defined receiver (SDR) that uses a common IC for the receiver and simple filtering. Its intended use is for TV, FM and DVB reception. It can be hacked, using the right drivers to be a very capable and cheap receiver. Fot further information see here[http://www.rtl-sdr.com/]. eBay will be able to offer you good value.
 
  
 
== Build Sequence ==
 
== Build Sequence ==

Revision as of 10:48, 4 March 2016

SatNOGS Rotator v3
SatNOGS Rotator v3
Rotator Information
Type: Az/El
Cost: {{{cost}}}
Release Information
Status: Beta
Latest Release: Torx Flathead (v3.0)
Repository: [1]
Documentation: [2]
 


Intro

v3 marks a major re-haul of the SatNOGS Rotator design, with learnings from v2 applied. You can see a lot of the thinking and background research that was conducted prior to v3 development in this thread.

Specifications

' SatNOGS v3 Rotator
Plastic Parts 26
Non Printed Parts approx. 345
Cost ~ $220
Controller Electronics SatNOGS Rotator Controller
Type Az/El (possible X/Y)
Motors 2x NEMA 17 Stepper or 2x DC Motors
Frame Material Aluminum T-slot 20x20
Pro
Con

Sourcing

3d Printing at a Fab Lab or you local hackerspace- If you don't have your own 3d printer then a local Fab Lab or hackerspace may be able to do it for you. Fab Labs and hackerspaces are places that have invested in the machinery and you can take the designs to them. Generally they need .stl files to import into the software that runs the machines but this should be discussed with the Fab Lab or hackerspace. You then pay for the colume of material or time or a combination of the two for each of the parts or any other agreement in place. FabLabs:[3] Hackerspaces:[4]

T Slot - If you don't want to cut the pieces yourself then here is a UK supplier[5] Hidden corner connectors - AliExpress gave the cheapest supplier

Stepper Motors - eBay

Belts - eBay

Fixings / Pipe - eBay

Build Sequence

  • Make sure you have all parts
  • Follow the instructions for mechanical assembly
  • Once mechanical assembly is ready, construct the SatNOGS Rotator Controller and connect it to the assembly.
  • You are ready! Proceed with testing.


Test Sequence

Test sequence needed


Documentation