Difference between revisions of "Raspberry Pi"

From SatNOGS Wiki
(Correct values for SATNOGS_RX_DEVICE)
Line 45: Line 45:
  
 
== Setup ==
 
== Setup ==
SSH to the Raspberry Pi with user "pi" and password "raspberry" (no quotes).  Run "sudo satnogs-setup" to set basic configuration.  When it's done, the Raspberry Pi will reconfigure itself; this may take some time.
+
 
 +
SSH to the Raspberry Pi with user "pi" and password "raspberry" (no quotes).  Run "sudo satnogs-setup" to set basic configuration. Select "quit" when you are finished, and the Raspberry Pi will reconfigure itself; this may take some time.
  
 
* Note: you can always reconfigure the software by running "sudo satnogs-setup -n" again.  
 
* Note: you can always reconfigure the software by running "sudo satnogs-setup -n" again.  

Revision as of 22:03, 1 October 2017

Intro

The Raspberry Pi 3 is the reference platform for SatNOGS. As of September 2017, there are two methods of installing the SatNOGS client on a Raspberry Pi:

  • Using Fedora for ARM, and following the instructions at satnogs.readthedocs.io
  • Installing the custom-built SatNOGS Raspbian image

Fedora

Start by downloading the "Server" or "Minimal" image from the the Fedora ARM project page. After that, follow the instructions at satnogs.readthedocs.io.

Raspbian

Download

The latest Raspbian SatNOGS image artifacts can be downloaded from GitLab.

Artifacts list

The current artifacts list consists of:

  • A Zipped image file
  • An Image info file
  • A SHA256 checksums file

Data integrity verification

You should verify the data integrity of the artifacts by checking the SHA256 checksums. On Linux, run sha256sum -c sha256sums in the directory where the artifacts are downloaded

Example:

$ sha256sum -c sha256sums 
2017-09-10-Raspbian-SatNOGS-master-lite.info: OK
image_2017-09-10-Raspbian-SatNOGS-master-lite.zip: OK

Flashing

Follow the usual Raspbian flashing instructions, and boot your Raspberry Pi.

Networking

If you are using wired Ethernet you should get connectivity right away. If you are using wireless then see this doc for network configuration instructions.

Setup

SSH to the Raspberry Pi with user "pi" and password "raspberry" (no quotes). Run "sudo satnogs-setup" to set basic configuration. Select "quit" when you are finished, and the Raspberry Pi will reconfigure itself; this may take some time.

  • Note: you can always reconfigure the software by running "sudo satnogs-setup -n" again.

Basic setup

  • SATNOGS_API_TOKEN: The API token assigned to your ground station on the SatNOGS Network website.
  • SATNOGS_RX_DEVICE: If you are using an RTL-SDR, this is rtlsdr. Other devices supported by gr-satnogs include usrpb200, usrp2, airspy or hackrf; a complete list can be found here.
  • SATNOTS_STATION_ELEV: The elevation of your ground station in metres.
  • SATNOTS_STATION_ID: The ID assigned to your station in the SatNOGS network site (either stage or prod).
  • SATNOTS_STATION_LAT: The latitude of your station. North is positive, south is negative.
  • SATNOTS_STATION_LONG: The longitude of your station. East is positive, west is negative.
  • HAMLIB_UTILS_ROT_ENABLED: Whether or not to enable the Hamlibs rotator daemon. Rotctld is a software daemon that provides a network server to control a rotator on a serial port. Note: even if you do not have a rotator, you'll want to enable this; see the next option for details.
  • HAMLIB_UTILS_ROT_OPTS: Options for rotcld. If you don't have a rotator, set this to -m 1; see here for details.

Updating

To update SatNOGS software, re-run sudo satnogs-setup. This will pull the latest Ansible playbook and update if necessary.

Raspbian packages can be updated using the normal APT updating methods (e.g. apt-get upgrade or aptitude).

WARNING: An update can potentially interrupt a running observation!