Difference between revisions of "Software Defined Radio"

From SatNOGS Wiki
m
(14 intermediate revisions by 3 users not shown)
Line 1: Line 1:
==SDR==
+
{{DISPLAYTITLE:Software Defined Radio}}
Based on the versatile
 
[http://www.realtek.com.tw/products/productsView.aspx?Langid=1&PFid=35&Level=4&Conn=3&ProdID=257 RTL2832U chip], SatNOGS is using R820T RTL-SDR as the default signal receiver and tuner. The R820T RTL-SDR is currently the cheapest, most common, and most performing solution available in terms of general sensitivity having a frequency range of 24 – 1766 MHz. The stack allows usage of other receivers too (like amateur radio transceivers) through the usage of rigctld (part of [https://sourceforge.net/projects/hamlib/ Ham Lib project]).
 
  
==HW Radio==
+
SatNOGS can use a variety of SDRs.  The most cost-effective solution is to use an RTL-SDR with a Raspberry Pi.  More advanced SDRs can also be used, but they require more processing power than what a Raspberry Pi can offer.
 +
 
 +
=== RTL-SDR: RTL2832U & R820T2-Based Software Defined Radios ===
 +
SatNOGS uses the RTL-SDR as the default signal receiver and tuner.  The RTL-SDR is based on two chips -- the versatile [http://www.realtek.com.tw/products/productsView.aspx?Langid=1&PFid=35&Level=4&Conn=3&ProdID=257 RTL2832U chip] and the [https://rtl-sdr.com/wp-content/uploads/2013/04/R820T_datasheet-Non_R-20111130_unlocked.pdf R820T tuner]. The RTL-SDR is currently the cheapest, most common, and most performing solution available in terms of general sensitivity having a frequency range of 24 – 1766 MHz.  A metal enclosure with SMA connector is preferred, along with a stable TCXO (low ppm).  HF coverage is optional.
 +
 
 +
These RTL-SDR "dongles" are known to work with Raspberry Pi 2 or greater:
 +
* [https://www.nooelec.com/store/sdr/sdr-receivers.html NooElec NESDR SMArt]
 +
* [https://www.rtl-sdr.com/buy-rtl-sdr-dvb-t-dongles/ RTL-SDR Blog R820T2 RTL2832U]
 +
* Full band UV HF RTL-SDR USB Tuner Receiver
 +
 
 +
=== Advanced Software Defined Radios ===
 +
The following advanced SDRs are supported by SatNOGS.  These may require more processing power than a Raspberry Pi 3b can offer.
 +
* [https://www.ettus.com/product/category/USRP-Bus-Series USRP b200]
 +
* [https://www.ettus.com/product/category/USRP-Networked-Series USRP2] (not compatible with the SatNOGS client on Raspberry Pi 3)
 +
* [https://airspy.com/ Airspy] (not compatible with the SatNOGS client on Raspberry Pi 3)
 +
* [https://greatscottgadgets.com/hackrf/ HackRF One] (not compatible with the SatNOGS client on Raspberry Pi 3)
 +
 
 +
=== References ===
 +
* [https://www.rtl-sdr.com/rtlsdr4everyone-review-of-5-rtl-sdr-dongles/ Review of 5 RTL-SDR Dongles]
 +
* [https://hackaday.com/2017/09/05/19-rtl-sdr-dongles-reviewed/ 19 RTL-SDR Dongles Reviewed]
 +
* [https://www.rtl-sdr.com/review-airspy-vs-sdrplay-rsp-vs-hackrf/ Review: Airspy VS. SDRplay RSP VS. HackRF]
 +
[[Category:SDR]]
 +
[[Category:Radio]]
 +
__NOEDITSECTION__

Revision as of 20:32, 2 February 2019


SatNOGS can use a variety of SDRs. The most cost-effective solution is to use an RTL-SDR with a Raspberry Pi. More advanced SDRs can also be used, but they require more processing power than what a Raspberry Pi can offer.

RTL-SDR: RTL2832U & R820T2-Based Software Defined Radios

SatNOGS uses the RTL-SDR as the default signal receiver and tuner. The RTL-SDR is based on two chips -- the versatile RTL2832U chip and the R820T tuner. The RTL-SDR is currently the cheapest, most common, and most performing solution available in terms of general sensitivity having a frequency range of 24 – 1766 MHz. A metal enclosure with SMA connector is preferred, along with a stable TCXO (low ppm). HF coverage is optional.

These RTL-SDR "dongles" are known to work with Raspberry Pi 2 or greater:

Advanced Software Defined Radios

The following advanced SDRs are supported by SatNOGS. These may require more processing power than a Raspberry Pi 3b can offer.

  • USRP b200
  • USRP2 (not compatible with the SatNOGS client on Raspberry Pi 3)
  • Airspy (not compatible with the SatNOGS client on Raspberry Pi 3)
  • HackRF One (not compatible with the SatNOGS client on Raspberry Pi 3)

References